Q1// long shunt compound generator supplies 600 KW, 1200V shunt field resistance =75 n, armature resistance=0.030, commutating field winding resistance=0.011n, series field resistance%-D0.0120, divertor resistance=0.0360, at 60 r.p.m. determine the percentage increase in flux per pole required to generate 1600 V at 40 r.p.m.

Q1// long shunt compound generator supplies 600 KW, 1200V shunt field resistance =75 n, armature resistance=0.030, commutating field winding resistance=0.011n, series field resistance%-D0.0120, divertor resistance=0.0360, at 60 r.p.m. determine the percentage increase in flux per pole required to generate 1600 V at 40 r.p.m.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2-A 4- pole lap-wound, 900 r.p.m shunt generator has armature and field resistances of 0.442 and 175Q respectively. The armature has 440 conductors and the flux per pole is 0.07 Wb. if the load resistance is 102.Calculate the terminal voltage and load current delivered by the generato
An engineer is designing 4-pole DC generator with 30 conductors by using simplex two-layer wave- winding method. Sketch the armature winding by showing the proper calculations.
The series field winding of a 170 kW, 250 V, 1450 rpm compound generator has a resistance of 0.00306 ohm. What will be the required resistance (in Ohm) of a noninductive diverter that will bypass 27 percent of the total armature current? "
4. The portion of the flux that goes through one of the transformer coils but not the other one is called. A) Average flux C) Total flux B) Mutual flux D) Leakage flux 5. The ------- are represented in the induction motor equivalent circuit by the resistor Rc (or the conductance Gc). A) Stray losses. C) Air-gap losses B) Friction and windage losses D) Core losses 6. The per-phase voltage Vo can be calculated by dividing the total voltage on. A) √3 B) √1.404. C) √0.707. D) √2.
1A. Which of the following is/are a method of providing field excitation for a DC generator. a) separately excited shunt b) self-excited series c) self-excited shunt d) all of the above 1B. Which type of field winding typically has the higher resistance? a) series b) shunt
An 145-pole d.c. shunt generator with wave wound armature having 455 conductors, has to supply a load of 120 lamps each of 145W at 230 v. The flux per pole is 14 mWb and Ra = 1.8 ohms, Rsh355ohms. What will be the %3D load current and e.m.f generated . Consider brush drop of 1v/brush. Load Current Generated EMF
(a) A 6 pole generator with lap wound armature has 135 slots each having 14 conductors. The flux per pole is 20 mWb. At what speed must the armature rotate to give an induced EMF of 210V. (b) What will be the voltage developed, if the winding is wave connected and the armature rotates at the same speed
the armature of a 12 pole wave wound dc shunt generator has 50 slots with 12 conductors per slot. the generatoris running at a speed of 625 rpm and supplies a resistive load of 15 ohm at a terminal voltage 350v. the armature and the field reisitance are0.5 ohm and 70 ohm respectively. find the armature current,generated emf and flux per pole
The shunt field winding of a shunt generator has a resistance of 80ohms at 20 degrees Celsius. After several hours of continuous operation, the winding temperature rises to 50 degrees Celsius. How much is the winding resistance under this condition. Assume the resistance temperature coefficient of copper to be 0.004 ohm per degree at 0 degree Celsius. *
Please it ASAP for an upvote.