Q1/ It is required to design a concrete mix using the American Concrete Institute method for use in pouring the ceiling of the building of the Technical College at the Technical Institute / Architecture that meets the following requirements: 1- Amount of precipitation = (8-10) cm 2- The maximum size of the coarse aggregate = (40) mm 3- Compressive strength at the age of (28) days = (20) Newtons / mm 2 4- Dry compacted weight of coarse aggregate = (1600) kg / m3 5- Relative density of coarse aggregate (2.68), fine aggregate (2.64) and cement (3.15) 6- Fineness calibrator for sand = (2.8) %3D %3D

Q1/ It is required to design a concrete mix using the American Concrete Institute method for use in pouring the ceiling of the building of the Technical College at the Technical Institute / Architecture that meets the following requirements: 1- Amount of precipitation = (8-10) cm 2- The maximum size of the coarse aggregate = (40) mm 3- Compressive strength at the age of (28) days = (20) Newtons / mm 2 4- Dry compacted weight of coarse aggregate = (1600) kg / m3 5- Relative density of coarse aggregate (2.68), fine aggregate (2.64) and cement (3.15) 6- Fineness calibrator for sand = (2.8) %3D %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the suitability of the aggregate, with the gradation tabulated below, for use in Portland cement concrete. Review the grain size distribution to determine if it meets all of the relevant specifications for use in concrete (i.e. gradation limits, fineness modulus and % fines). Refer to the specification for concrete aggregates (Table 7 – 10) below: Grain Size (mm) % Passing Cum %Retained 25 100 19 100 12.5 100 9.5 100 4.75 95 2.36 85 1.18 55 0.6 30 0.3 15 0.15 8 0.075 6
Standard deviation is 3.6 MPa
I need the answer as soon as possible
The requirements and material properties of an air entrained concrete mix are given below. Calculate the weights of the components of 1 m3 of concrete. Water content: 200 kg/m3 Air content: 7.5% W/C: 0.45 (By Weight). Dry aggregate volume in 1 m3 concrete mixture: 0.44 m3 Specific Gravity (g/em3 ) water absorption capacity (%) Total Moisture (%) Cement 3.15 Fine aggregate (saturated surface dry) 2.65 1.3 5.5 Coarse aggregate (saturated surface dry) 2.7 0.5 1.5 Dry unit weight of coarse aggregate is 1,500 kg / m3. 'kind
Give the conclusion and recommendation of this experiment: DETERMINATION OF SPECIFIC GRAVITY AND ABSORPTION OF FINE AGGREGATES.
For the given concrete mix design below, calculate the field weight of the ingredients in kg's if the absorption capacities of both aggregates are 2% and both aggregates became oven dry after a very sunny day? Weight in kg per m³ 300 Ingredient Cement Water SSD Coarse aggregate SSD Fine aggregate Water: Seç Coarse aggregate: Seç Fine aggregate: Seç... → + 150 1020 816
I need answer within 20 minutes please please with my best wishes
why do we need to know the Specific Gravity and Absorption of Fine Aggregate, Surface Moisture of Fine Aggregate, and how it is important in concrete
a) How various properties of aggregates affect workability of concrete? b) If the peak load of concrete cylinder in compression is 70,000 pounds, find the crushing strength of concrete? (Hint: concrete cylinder dia is 6in). SIR, PLS GIVE ME PROPER AND CORRECT ANSWER WITH FULL DETAILS. SUBJECT: CONCRETE TECHNOLOGY
This course EHide blocks An aluminum pipe is filled in concrete is subjected to a pure compressive force as shown in the figure below. Determine the factor of safety against compressive stress acting on the column. The pipe has an outer diameter of 45 mm and inner diameter of 35 mm. The aluminum and the polymer concrete have the following material properties: Young's modulus: Eal = 70 GPa (aluminum), Ecr = 30 GPa (concrete). Yield compressive strength: Sy-al = 180 MPa (aluminum), Sy-cr 60 MPa (concrete). 100 kN 500 mm Select one: O FS = 1.5 O FS = 1.7 O ES- 19 5:45 PM 86°F Light rain ENG 6/18/2021
4b. Deformation occurs on freshly lay concrete when it finally set or harden.discuss the various causes for dimensional changes in the hardened concrete.
Concrete basics.