Q1/ If the message signal is m(t) = cos (1000rt)cos (3000nt): a. Sketch the spectrum of m(t). b. Sketch the spectrum of the DSB-SC signal m(t)cos(10,000nt). c. Identify the upper sideband (USB) and lower sideband (LSB) spectra.

Q1/ If the message signal is m(t) = cos (1000rt)cos (3000nt): a. Sketch the spectrum of m(t). b. Sketch the spectrum of the DSB-SC signal m(t)cos(10,000nt). c. Identify the upper sideband (USB) and lower sideband (LSB) spectra.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

• Consider a information signal: m(t) = 20 cos (2000JI t), carrier signal: c(t) = 50 cos (105 Jt). a) Find and sketch the AM wave for 75% modulation. b) Sketch the spectrum of this AM wave. c) Find the power across a load of 100 2. (
Question 4. Select the statement that best describes the PM wave.a. Carrier phase angle changes represent the PM modulated signal, however, unlike FM and AM modulatedcarriers, it is not always easy to see these phase changes in the plot.b. The FM signal accurately represents the message.c. Although PM and FM techniques are classified as angular modulation techniques, they cannot be usedinterchangeably (i.e., modulated with FM and demodulated with PM, and visa versa).d. All statements are correct.
Q7. Figure Q7(a) shows the spectrum of a frequency modulated waveform with a sinusoidal modulation. 12 4.8 5.0 5.2 5.4 5.6 5.8 6.0 Frequency/MHz Figure Q7: (a) Spectrum of a frequency modulated waveform with a sinusoidal modulation. (a) Is this modulated waveform described as narrowband or as wideband? (b) What is the value of the carrier frequency? (c) What is the value of the modulation frequency? (d) Determine the value of the peak frequency deviation. Plots of Bessel functions of the first kind are provided below in Figure Q7(b) to assist you. (e) Estimate the fraction of the total signal power at the carrier frequency. (f) Detection of such a frequency modulated signal is usually accomplished with the use of a discriminator. Describe the function of a discriminator. (g) What is the equivalent AM modulation index obtained if this signal in Figure Q7(a) is demodulated with a high-pass RC filter discriminator? J„(x) 1.0 0.8 0.6 0.4 0.2 -0.2 -0.4 Figure Q7: (b) Bessel functions of the…
A modulating signal �(�) is given by: (b) �(�)=��(100��)��(500��) (i) Sketch the spectrum of �(�). (Hint: use the trig identity for the product of sines.) (ii) Sketch the spectrum of the DSB SC signal 2�(�)��(1000��) and find the algebraic expression of the spectrum. iii) From the spectrum sketch in part (ii), suppress the LSB part to sketch the USB spectrum. (iv) Knowing the USB spectrum in part(iii), write the expression �USB (�) for the USB signal. (v) Repeat parts (iii) and (iv) to obtain the LSB signal �� (�).
1. a. For a baseband signal m(t) = cos wmt = cos 2n fmt, Find the DSB-SC signal and sketch its spectrum. Identify the USB and LSB. b. For each of the baseband signal: (i) sketch the spectrum m(t). (ii) sketch the spectrum of the DSB-SC signal m(t)cos 10,000rnt, (ii) Identify the USB and LSB. (i) т() = cos 1000xt; (ii) m(t) (iii) m(t) = cos 10007I cos 30007 {, с. You are asked to design a DSB-SC modulator to generate a modulated signal km(t) cos (wei+0), where m(t) is a signal band-limited to B Hz. Figure P4.2-4 shows a DSB-SC modulator available in the stock room. The carrier generator avaitable generates not cos wet, but cos³ wct. Explain whether you would be able to generate the desired signal using only this equipment. You may use any kind of filter you like. (a) What kind of filter is required in Fig. P4.2-3? (b) Determine the signal spectra at points b and c, and indicate the frequency bands occupied by these spectra. km(1) cos at MS) Filter cos ca (a)
2 (AM) A 10 V amplitude sinusoidal signal is used as a modulating signal to generate an AM signal with modulation index 0.8. What is the amplitude of the carrier? What is the power of the side bands? What is the efficiency of the modulated signal?
1 Can we generate FM signal using PM modulator? * Yes No
Subject:communication. Need solution
Q2: A modulating signal is used to modulate a carrier signal(AM modulation). Let Pr . Pc. PSB. PuSB. PLSB and u are the total power, carrier power, side band power, upper side band power, lower side band power and modulation index respectively. Prove the following: a. Pc = Pr () c. Pusn = Pisn =) Pr m2 b. Psn = Pr %3D 2+m2 LSB 2+m? (2+m2
A carrier signal given by 10cos2r×108t volt is FM modulated by single tone message 4cos2nx103t volt if the modulation constant is 1000 Hz/Volt a) Compute max. frequency deviation and deviation ratio. b) Write the equation of modulated wave. c) Sketch the spectrum. d) Calculate sidebands carrier and total power.
The baseband signal modulates a 98 kHz carrier sine wave. Using frequency and amplitude labelling similar to that in Figure 2, sketch the spectrum of the modulated signal using a template, similar to that in Figure 3, for the following modulations: AM with the amplitude of the carrier wave being 20 V DSBSC SSB – the lower sideband SSB – the upper sideband
B- Draw the modulation and demodulation block diagram of AM-VSB. C- If m(t)-Am cos(wmt) v, find and sketch the spectrum of AM-DSB signal.