Q1): For the circuit shown in Figure 1,let (vin =100µv(p.p) and ß = 150 ). 10V 47K 4.7K Vo a) Determine the VCE, and ICo ? b) Calculate the VCE(cut-off) and IC(sat.) ? c) Find power gain? Vi 10u 10µ 100µ Q2): For the circuit shown in Figure 1, if connected as multistage by capacitively-coupled:- 10K 1K 1. The AV, (- 56.8, - 65.8, - 68.5, - 86.5 and other) Figure 1 2. The AV2 soolve Q2 only (- 179, - 197, - 19.7, and other) 3. AVtotal(dB) (68.2, 62.8 86.2, 82.6 and other) OTW

Q1): For the circuit shown in Figure 1,let (vin =100µv(p.p) and ß = 150 ). 10V 47K 4.7K Vo a) Determine the VCE, and ICo ? b) Calculate the VCE(cut-off) and IC(sat.) ? c) Find power gain? Vi 10u 10µ 100µ Q2): For the circuit shown in Figure 1, if connected as multistage by capacitively-coupled:- 10K 1K 1. The AV, (- 56.8, - 65.8, - 68.5, - 86.5 and other) Figure 1 2. The AV2 soolve Q2 only (- 179, - 197, - 19.7, and other) 3. AVtotal(dB) (68.2, 62.8 86.2, 82.6 and other) OTW

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q. An Oil and Gas Company has gave us a contract to design a temperature measurement instrument The instrument has to measure temperatures between 0 to 100C using RTD PT100 1- The Wheatstone bridge must be leaner and proportional 2- Wheatstone bridge must start from zero volts Design the instrument if you know the following The resistance of the RTD PT100 is =100 Ohm's at 0°C and 139.5 Ohm's at 100°C the input of the circuit is 5V and the output is 0.1V Given the following table is the reading of the instrument for some temperature values when R1=R2=R3=100 Ohm's Temp Vout 20 0.11 40 0.19 60 0.30 80 0.36 100 0.41
1. Calculate the lc in figure below with beta = 80 Vcc= 12 V 550k Select one: O a. 0.174mA O b. 1.75mA O c.0.164mA O d. 1.64mA 1.5k
A stabilization circuit has a stability factor of 0.04 and an internal resistance of 5 2. The unstabilized voltage can vary between 75 and 100 V, and the load current can vary from 40 to 80 mA. Determine the maximum and minimum values for the stabilized load voltage.
for the Circult Shown in Figure If Vcc = 35 V, I = 3.88mA Determinei- 1- The Value of RE ? 2- The Value of Beta ? 3-Tie Value of VB ? Vi HH 4-VC =? RE
R, R. R, out R. R. out out 20kn Figure 3 Figure 1 Figure 2
2 - Işınımsız birleşim özelliği gösteren yarı iletken malzemeler hangi alanda kullanılır?I. LedII. Lazer diotIII: DoğrultucuIV. Yükseltici In what area are semiconductor materials used that have non-radiative junction properties?I. LedII. Laser diotIII. RectifiersIV. Amplifiers A) II-III B) I-II C) II-IV D) I-III E) III-IV
Q1: for a silicon transistor in the figure below = 200 dc {What is the voltage between the collector and emitter VCE, drawing the load line and finding the Q point
Give prop ex p
D-MOSFET: lVtl= 2 V, Idss =10 mA, Is=1.6 mA, rd=14 K, RL=2 K. Calculate the dc drain-to-source voltage. Please write your answer as a V and don’t use units in the answer. Please use one digit after the dot.