Q1) Find the value of (Ix) and find the power supply by 42 and 52 using (K.V.L) ? 2IX 8A

Q: 4-12. The output of the supply in problem 4-11 shows 500 mV ac ripple when it is loaded. Find its…

A: In this question we need to a ripple percentage .

Q: Two wattmeters are connected to measure the power consumed by a 3- load with a power factor of 0.4.…

A:

Q: Find the equivalent resistance seen by the generator 10v. 52 52 Ic 10V 30 42 122 Vo 52 72 elect one:…

A:

Q: Four identical dry cells with an emf of 1.4 volts and internal resistance of 0.06 ohm each, are…

A:

Q: 7s 52 +4,

A: The detailed solution is provided below.

Q: The sizes of the given circuit elements are given below. What is the average power delivered by the…

A: In a single-phase transformer dot convention of the winding is of importance. In the given circuit…

Q: If in warehouse scale computer we have the following 1- critical load = 10 MW ( Mega Watt) 2…

A: PUE stand for Power usage effectiveness. It is the metric use for  determining the energy…

Q: Example 01:-Four arms of a Wheatstone bridge are as follows: AC = 100 N, BC = 10 2, BD = 4 2, DA =…

A:

Q: For R1=4, R2-8, K-6, and I=45 in the circuit shown below, use KCL & KVL to find the following: R1 Ω…

A: In these questions We need to choose the correct options We know power P= VI Current I= V/R We are…

Q: Given : Vs : 500 volt RI :3 ohm X1 :5 ohm R2 : 0,03 ohm X2 :0,05 ohm Rc : 150 ohm Xm : 750 ohm…

A: For the given arrangement, the impedance of the load is purely resistive and can be calculated as…

Q: The numerical values for the currents and voltages in the circuit are given in the table below. Find…

A:

Q: The numerical values for the currents and voltages in the circuit are given in the table below. Find…

A: Find the power of the each element in the above given circuit ?

Q: 3. A series RC circuit with R=4kQ and C=0.40uF is connected to an AC voltage sour v(t)=100sin200t.…

A: In this question,  Find the rms current, phase difference between current and voltage.  Power…

Q: Choose the correct value of the Output power of the PV cell for the values of solar input power 50W…

A: Given :    Solar input power Pin = 50 W    Efficiency = η    Po = output electrical power    pin =…

Q: What is the difference of the readings between B/A and A/B sections in the oscilloscope of Multisim?

A: If we taken voltage across a-b terminal is =+(positive some voltage) If we taken voltage across b-a…

Q: 12 12 JAV التاريخ 7 Ji ukn Allee いま 2V Ah

A:

Q: Which of the following is the average power given by the Is current source according to the given…

A:

Q: When does maximum frequency deviation occur in an FM signal? -It occurs during the transition of…

A: The explanation is as follows.

Q: Find the currents. 3800 V 50 N 80 N 12 40 2 3400 V

A: In this question,  What is value of currents as shown in the circuit.

Q: 1000 208V 400H z 3uF For the circuit given, what is the current?

A: we have given R=100ΩC=3μFAc source 208V ,400Hz

Q: Find the voltage between points a and b (in V). A. 3 B. -5 C. 6 D. 1 70 m 40 * 12V m 20 9V www 11₂

A:

Q: 1. A wattmeter measures power by measuring the product of the current through and the voltage across…

A:

Q: Q1) For the following circuit Find the currents I1, 12, V1 and V2. V2 V1 24 kN 24 kN 12 kN + E E 72…

A:

Q: Draw the relationship between V & I

A: For this, we can easily draw the relation between Voltage V and current I .

Q: Find the voltage between points a and b (in V). A. 3 B. -5 C. 6 D. 1 79 m 40 12V m 20 112

A:

Q: 10. Consider figures A and B.below and find the curreat in amperes in the 12 resistor of fie 22 ER…

A:

Q: Vbatt is 14.5V to avoid overcharging the battery. Vbatt falls to 11.4V due to discharge at night.…

A:

Q: 7- when the temperature of PV module increases a- The short circuit current and open circuit voltage…

A: PV module : PV module is also known as solar panels which absorbs the solar energy in form of solar…

Q: 50 ww ww 60 20Ω | 15 A

A:

Q: Two electric bulbs rated at watt, V volt and watt. V volt are connected in series across V volt. The…

A: The total power consumption by the series combination of bulbs can be calculated by using ohms law

Q: In what ways are integrated circuits better than discrete ones.

A: Brief description: In the above given question they want to know the advantages of integrated…

Q: power factor is measured in Select one: O a. no unit b. watt C. VA d. VAR

A: Power factor: It is the ratio of active power P to the apparent power S. It is denoted by cosθ. So,…

Q: Use Nodal Theorer to solve for the cit 7 45 4 75.8& 1201 4 Find the total power. unsumed by the…

A: In this question we will find power consumed by circuit.....

Q: For the circuit shown in Figure, find the following: a. The magnitude of current in the circuit, I.…

A: To find current and power dissipated in each resistor  And value of unknown resistance R

Q: In the given figure, find the current V2 in volts. 8 S2 3 2 V1 + v, V2 I2 3552 36 V 342 $42

A: We will use krichoff's current law to calculate unknown voltage .

Q: Use Kirchhoffs law to determine the values of the currents flowing in each of the batteries.…

A:

Q: 4H Q.2: For the magnetically coupled circuit shown, when V-100cos(344t) Volt, M,=4.5H & M2-4H. Find…

A:

Q: How the load factor is affected by the block meter rate structure or tariff

A: Load factor is define as the ratio of an average to a maximum load. load meant by the kilo-watt…

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.