!!!ProblemsQ1: Find the time period for a lump system to reach the average temperature0.693is (T; + T,)/2Ansh.AQ2: The temperature of a gas steam is to be measured by a thermocouple. Determine thetime it takes to register 99% of the initial AT . For junction k =35 W/m.°Cp =8500kg/m' and C,-320 J/kg.Ans : 38.5 sGasJunctionDh, T.T1)

Solution (1): The expression for the lumped system is given by, T-T∞Ti-T∞=e-hAsρVC×t Here, T is the…

Answered: Q1: Find the time period for a lump…

Engineering

Mechanical Engineering

Q1: Find the time period for a lump system to reach the average temperature 0.693 is (T; + T,)/2 Ans h.4 PC,V

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need answer within 5 minutes please please with my best wishes
2) The following heating system for a room is considered: ATroom = K1 | Qodt, Qo = Qin - Qout Qout = K2AT,0om room Qin = K3(ATrad – ATr00m) where AT is the room temperature and AT is the radiator temperature. What is room rad the stationary room temperature, if the radiator temperature is 50C and if K1 = 104, K2 = 4, and K3 = 1? A. 40°C В. 20°C С. 10°C D. 30°C Е. None of the previous answers are correct.
Please solve and include units. Thanks!
b) For an Otto Engine the temperature at the end of combustion is 280 K. If the temperature in the gas side and coolant side of the wall are 177 °C and 127 °C and cylinder wall thickness is 5 mm;
I need the answer in 15 minutes please best wishes Ahmed.
Write the simplified ENERGY BALANCE equation for each process based on the givenconditions. Start from the general energy balance form, and arrive at the correct balance byexplaining any addition, deduction, or change in the equation.Use the following as subscripts in your answer: 1 = initial system state; 2 = final system state; i = inletstate, e = exit state.a. A rigid tank transferring heat to its surroundings. b. The seal of an insulated system with a high energy substance is broken, causing the contents tobe evacuated until only 20% of the initial internal energy remained. No heat transfer was detectedin the system’s boundaries. c. Consider a hydroelectric power plant operating in steady conditions, wherein the system consistsof two water reservoirs with a height difference Δz, with a Francis water turbine placed betweenthe stream connecting both.
令l。 A:0 ۲۳ شباط تحریر > Subject : Engineering Thermodynamics 1 2 nd I Production , Industrial class Date : 24/2/2021 Branch A system contains co.15 m²) of at gas * pressure of C4 ber ) and s 150 °c) . It is ex panded isothermally till the falls pressure is then cooled gas to ( 1 bar ). The a cons tant pressure till its heat Lost ( 70 KJ ). Draw the processe at on (P-V) sses diagram , and determine the net work done. [ Take, KT 1 Cy = 0.714 KJ
answer and feedback attached, can show steps more clearly please
Correct and Fast Please
3 A rigid tank with volume of 1 m contains 2 kg of water at 100 C. The tank is now heated. If a safety pressure valve is installed, at what pressure should the valve be set to have a maximum temperature of 200 C? 00 Select one: on O a. 534.33 b. 478.83 Oc.592.43 Od.431.42 Oe None of the above Electric heateris used to heat 0 63 liters/minute of water (C, = 4.18 kJ/kg.K, density =1000 kg/m) from 25 °C to 65 C What is the current (in Ampéres) that must be supplied to this heater if the supplied voltage is 220 vered of 2.00 eslion Select oner 0a 10.37 O6 11 97
Please I need the answer in 30 minutes
give the a) A turbine connected to an electric generator through a gearbox can be modelled as illustrated in Figure 1 = 951 kgm² J2 = 950 kgm² equivalent inertias of the rotary system. The shafts provide a stiffness of k1 = 9.9x10¹Nm/Rad k2 = 4.9x106Nm/Rad spectively. The letters in the parameters represent digits of student numbers: A is the third digit, B is the fifth digit, D is the sixth digit, and F is the seventh digit. i) Draw free-body diagrams ii) Write the equations and put them in matrix form iii) Calculate the dynamic stiffness values iv) Find the natural frequencies and draw mode shapes of the system v) Discuss the effect of coupling stiffness k₁₂ on the natural frequencies k₁₁ 01 k12 O Figure Q2.