Q1: Estimate the quantities of the following items of a two roomed building for the given plan using method of separate wall. The dimensions of 2 doors are (1.5m x 2.5 m), 4 windows (1.2 m x 1.5 m) and 2 shelves (1.2 m x 1.5 m). The thickness of lintel over doors, windows and shelves are 17 cm. The thickness of shelves is 17 cm. 1) Earthwork in excavation in Foundation 2) Lime concrete in Foundation 3) 1st class brick work in Foundation 4) 1st class brick work in Foundation in superstructure. 5.3m 0.3m 5m 0.3m 0.5m 3.5m 0.5 m -0.6m- G.L 0.3 m 0.3 m 0.3 m

Q1: Estimate the quantities of the following items of a two roomed building for the given plan using method of separate wall. The dimensions of 2 doors are (1.5m x 2.5 m), 4 windows (1.2 m x 1.5 m) and 2 shelves (1.2 m x 1.5 m). The thickness of lintel over doors, windows and shelves are 17 cm. The thickness of shelves is 17 cm. 1) Earthwork in excavation in Foundation 2) Lime concrete in Foundation 3) 1st class brick work in Foundation 4) 1st class brick work in Foundation in superstructure. 5.3m 0.3m 5m 0.3m 0.5m 3.5m 0.5 m -0.6m- G.L 0.3 m 0.3 m 0.3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

GIVEN THE FOLLOWING FIGURE A E G J K H L if each square measures 35.24 square meters and A= 5.84m, B=7.77m, C=8.08m, D=2.13m, E=8.35m, F=6.52m, G=1.59m, H=5.05m, I=2.06m, J=8.03m, K=2.55m, L=1.93m, and M=2.02m, determine the volume of the excavation in cubic meter. F.
Calculate the U-value for the wall:a) without regard to the studs;b) with the studs according to the λ - and U value method.c) Compare results. Show as a percentage how much U with studs is greater than U without Proportion of studs in construction: 45/600=0.075 (7.5%);Rsi (inside)=Rsu (in the air gap)=0.13 m2K/W
with formula
Derive the labor and equipment cost for a 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture based from the following crew team composition, output and given prices.1. Team and Daily Rates1- Project Engineer (P 2000/day)1 - Construction Foreman (P 1000/day)6 - Mason (P800/day)12 - Laborer (P500/day)2. Output of team is 13.5 cu.m per day.3. Equipment (minor tools) is 10% of the labor cost.
Determine the total toque for 4 cm square shaft using finite element formulation
Find the quantity of the following items for the partition wall from its footing to the bottom of the beam with 3 columns having a width of 300mm and a beam on top of the CHB having a depth of 400mm. Use 100 x 200 x 400mm CHB and assume that the total height is 4 meters from the top of its footing up to top of beam and the total length of the partition is 9 meters. Note: with 2pcs of 2.1 Om x 0.90m doors and no windows. 1. Quantity of CHB 2. Quantity of mortar (cement and sand) using class C mix 3. Quantity of plastering (cement and sand) using class A mix back to back
Determine the characteristics of the equivalent bar (area, moment of inertia and shape factor of the cross section) that allows replacing the wall of three basements shown. Data: Reinforced Masonry Wall Internally: E = 500,000 ton/m2 E/G = 2.5 Thickness = 0.15 m Base: 2.0m Height of each basement wall: 2.5m Equivalent bar reinforced concrete deformable by flexion and axial: E = 2,000,000 ton/m2
Derive the labor and equipment cost for a 1,000 sq.m 4" thick masonry wall using 1:5 mortar mixture based from the following crew team composition, output and given prices.1. Team and Daily Rates1- Project Engineer (P 2000/day)1 - Construction Foreman (P 1000/day)6 - Mason (P800/day)12 - Laborer (P500/day)2. Output of team is 13.5 cu.m per day.3. Equipment (minor tools) is 10% of the labor cost.
The following diagram shows a partial floor framing plan of an elevated walkway building connecting an airport terminal building to the adjacent garage. The concrete floor is not post- tensioned. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Framing members are not exposed to weather or in contact with soil. Per the ACI, what is the minimum slab depth? Consider both the interior slab and the cantilevered slab at the edge of the building. 30-0¹ B4 B4 B4 83 Column 52 SI 30-0 -Sab Mark Dean- B4 B4 B4 83 B 30-0¹ BI B2 B2 BI -Girder 12 A 1 3-4 Ei 13:4 05 40-0 to 2