Q1: determine the resultant of force as *.shown in figure 100 lb 150 Ib 100 lb 40 lb 100 lbT 150 Ib

Q: y F2 = 500 lb F1 = 200 lb 3. 60° B. 70° F3 = 800 lb 45° A

A:

Q: Determine the resultant force, FR, and its distance from D. 600 lb 800 lb F 800 lb 60° 60° 30 C 10…

A:

Q: Two masses are attached to a uniform meter stick as shown in the figure below. The masses of m1 and…

A:

Q: of

A:

Q: statics

A:

Q: 125cm EX.2: A bar 100cm long of cross-section 2cm 2cm is acted upon a force 1000kg modulus of…

A: Hi . there are two value of length given as it is not clear which one to use so we are considering…

Q: 4. The truss shown below is supported by a roller at A and a pin at C. Determine the reactions at…

A:

Q: A 150-lb force acts as shown on a 300-lb block placed on an inclined plane. The coefficients of…

A:

Q: Fundamental Problem 4.33 Replace the loading system by an equivalent resultant force and specify…

A: Given data : F1 = 25 KN and F2 = 18 kN TO find : FR , Thetha and d ?

Q: Determine the MAGNITUDE of the resultant F = 200 lb 888 F2 = 400 lb 888 00 888 ´F = 300 lb |F3 = 300…

A: to determine the resultant we first has to determine the incinations of forces F2 and F3let,θ=angle…

Q: Substitute: A=4, G=6 H=12 Determine the center of gravity of the built-up section with respect to…

A:

Q: The truss shown supports an automobile which has a mass of 2000 kg. Each member of the truss has…

A:

Q: If two forces 3 kg & 4 kg act at right angle to each other their resultant force will be equal

A: Given data : Force (P)=3 kgForce (Q)=4 kgθ=90∘

Q: The beam shown below is carrying a vertical shear force v. S IF

A: Given Data:Vu=53000 Nb=100mmh=170mmE=220GpaTo Calculate: Maximum shear stress.

Q: Determine the force (P) required to prevent block from moving, given that us = 0.4 and uk = 0.23. F…

A: Given data,  μs = 0.4 μk = 0.23 F1 = 803 unit θ = 33°   To find out the force P required to prevent…

Q: A steel bar 60 mm in diameter and 3 m long is surrounded by a shell of a cast iron 6 mm thick.…

A:

Q: 400 lb 400 lb 160 lb/ft 100 lb/ft MATHalino com 5 ft 5 ft 3 ft * 10 ft 6 ft *3 ft R1 R2 R3 R4 Figure…

A:

Q: Determine the force (P) required to cause impending motion, given that us = 0.38 and uk = 0.3. F1 =…

A: Given data,  θ = 34° μs = 0.38 μk = 0.3 F1 = 626   To find out the force required to cause impending…

Q: On the assembly shown on Figure 2, determine the components of all the forces acting on member ABCD.…

A: Consider the figure,

Q: Determine the value of EIy  at x = 3m from the left support, for the beam  loaded as shown in Figure…

A: Question is based on the simply supported beam carrying uniform load and moment . Magnitude of load…

Q: A rigid bar is carried by deformable steel and aluminum rods as shown in the figure. If P = 122 kN,…

A:

Q: The Howe roof truss shown in the figure carries the given loads. The wind loads are perpendicular to…

A: Given, To determine,The resultant and its intersection with AB.

Q: Determine the resultant of the four forces acting on the body shown. Ans. 214 lb 224 Ibr 200 lb 60°…

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: Fundamental Problem 4.33 Replace the loading system by an equivalent resultant force and specify…

A: Given : F1 = 25 KN F2 = 18 KN F2 is a force acting such that the hypotenuse is 5 To find : 1.…

Q: 2. The bar ABCD in the given figure below consist of three (3) cylindrical steel segments, each with…

A:

Q: F=250 lb 30 45° F = 375 lb |3D

A:

Q: Problem 4.135 Replace the force system by a wrench. Suppose that F₁ = 300 N and F₂= 200 N. (Figure…

A: Given : F1 = 300 N and F2 = 200 N to find : 1) F  2) M 3) x , z

Q: The correct unit of the force among the following is; O kg-m/sec O kg/m/sec O kg-m/sec^2 Okg/m/sec^2

A: Force,F=mass X acceleration=kg. m/sec

Q: For the forces shown below, the horizontal component of force F1 is . (Round the final answer to the…

A: To find Horizontal component of force F1

Q: Given the following, Determine the reactions for the beam. Show and explain step by step so I can…

A: Considering the given figure: 2P = (2)(5) = 10 lbP = 5 lbL = 12 ft  Explanation:In order to get RAV…

Q: Determine the resultant force at A. 2 ft Fo 490 lb Fr 600 lb 6 ft 4 ft 3 ft B 4 ft 2 ft 4 ft

A: Given: FC = 490 lb FB = 600 lb

Q: 2. The frame shown in the figure is hinged to rigid supports at D and E and roller supported at A.…

A: We need to find the reaction forces at the D and E

Q: Analyze the following figure if: h=1.5 m, d=3 m, x=4 m 3 kN D 3 kN

A: Given data:

Q: I. Compute the force of CD and DE of the truss given below: 2000 Ib 3000 lb D 60° 60° C 60° 60° A…

A:

Q: Determine the magnitude and the position vector AC in ft.

A:

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.