Q1) Consider the base plate of a 800-W household iron having a thickness of L=0.6 cm, base area of A=160 cm2, and thermal conductivity of k=120 W/m-°C. The inner surface of the base plate is subjected to uniform heat flux generated by the resistance heaters inside. When steady operating conditions are reached, the outer surface temperature of the plate is measured to be 85°C. Disregarding any heat loss through the upper part of the iron and taking the nodal spacing to be 0.2 cm, (a) obtain the finite difference formulation for the nodes and (b) determine the inner surface temperature of the plate by solving those equations. Insulation Resistance heater, 80 w 85°C Base plate

Q1) Consider the base plate of a 800-W household iron having a thickness of L=0.6 cm, base area of A=160 cm2, and thermal conductivity of k=120 W/m-°C. The inner surface of the base plate is subjected to uniform heat flux generated by the resistance heaters inside. When steady operating conditions are reached, the outer surface temperature of the plate is measured to be 85°C. Disregarding any heat loss through the upper part of the iron and taking the nodal spacing to be 0.2 cm, (a) obtain the finite difference formulation for the nodes and (b) determine the inner surface temperature of the plate by solving those equations. Insulation Resistance heater, 80 w 85°C Base plate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a permanent one-dimensional heat conduction on a flat wall of length L = 0.4 m and constant thermal conductivity equal to 0.9 W/m.K, without heat generation. a) If the inner wall is T(0) = 140°C and receives a constant thermal flux of q', = 400 W/m?, what is the temperature at the outer surface, T(L) = ? b) If T(0) = 50°C and the outside of the wall is exposed to air convection at 25°C and h=10 W/k.m?, what is the temperature on the outside surface, T(L)?
6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transiently
Q.3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. (10 Pts)
I need the answer as soon as possible
2- The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick. There are to be 100 fins per meter. The convective heat transfer coefficient, both for the wall and the fins, is estimated at 35 W/(m2 K). With this information, determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall. (take the case where the tip is exposed to convection) Ans(48 t= 2.5 mm 2.5 cm
Q3. A small electric heating application uses wire of 2 mm diameter with 0.8 mm thick insulation (k = 0.15 W/m°C). The heat transfer coefficient (ho) on the insulated surface is 31 W/m2°C. Determine the critical thickness of insulation in this case and the percentage change in the heat transfer rate if the critical thickness is used, assuming the temperature difference between the surfaces of the wire and surrounding air remains unchanged. - Wire Insulator air 12 0.8 mm
I need complete solutions and 4 decimal places in all solutions.
Q30) A 4-mm-diameter and 5-m-long electric wire is tightly wrapped with a l1-mm thick plastic cover whose thermal conductivity isk = 0.2 W/m °C. Electrical measurements indicate that a current of 15 A passes through the wire and there is a voltage drop of 8 V along the wire. If the insulated wire is exposed to a medium at T 30°C with a heat transfer coefficient of h = 15 W/m2 °C, determine the temperature at the interface of the wire and the plastic cover in steady operation. Also determine whether doubling the thickness of the plastic cover will increase or decrease this interface temperature..
In the continuous regime, there is a constant heat generation of q = 3×107 W/m³ in a one-dimensional wall with a thickness of 20 mm. The heat conduction coefficient of the wall material is k = 32 W/ mK. The temperature Ts on the wall surface is Ts1 = 127 ° C and Ts on the other surface is Ts2= 27 ° C. So, find where the highest temperature occurs in the wall?
8--The reactor from uniform carbide and graphite as a cylinder rod with diameter of 12 mm. The volumetric heat liberationis 3.88x108 W/m3 The thermal conductivity of the rod material is 85 W/mC.. Determine the heat losses from the rod and the surface temperature if the maximum temperature of the rod is 200C...Ans Tw=1940 C,,Heat losses=1.164 MW/m2.
Consider a homogeneous spherical piece of radioactive material of radius r0 = 5 cm that is generating heat at a constant rate of q.= 3.8x107 W/m3 The heat generated is dissipated to the environment T∞= 27°C and h = 110 W/m2°C steadily. The outer surface of the sphere is maintained at a uniform temperature (Ts) and the thermal conductivity of the sphere is k = 25 W/m°C. Assuming steady one-dimensional heat transfer, (a) express the differential equation and the boundary conditions for heat conduction through the sphere, (b) obtain a relation for the variation of temperature in the sphere by solving the differential equation, and (c) determine the temperature at the center of the sphere
a. The wall of a building has a surface area of 50 m2. The outside layer of the wall is 20 cm thick concrete with thermal conductivity kcon = .8 W/m-K. The inner layer is 10 cm thick balsa wood (kbalsa = .048 W/m-K) as an insulator. Outside temperatures of 47o C are expected, while an inside temperature of 21o C is maintained by the cooling system. Find the rate of heat transfer through the wall.