Q1: Circle the correct answer. 1. How many unknown support reactions are there in this problem? 40 hft A) Two forces and two couple moments B) One force and two couple moments C) Three forces D) Three forces and one couple moment 30 2. A general system of forces and couple moments acting on a rigid body can be reduced to a A) single force B) single moment C) single force and two moments D) single force and a single moment 3. The three scalar equations, E Fx EFy E Mo 0, are equations of equilibrium in two dimensions. A) Incorrect B) The only correct C) The most used D) Not sufficient 4. The forces on the pole can be reduced to a single force and a single moment at point A) P B) Q C)R D) S E) Any of these points. y 5. If a support prevents translation of a body, then the support exerts a on the body. A) Couple moment B) Force C) Both A and B. D) None of the above

Q1: Circle the correct answer. 1. How many unknown support reactions are there in this problem? 40 hft A) Two forces and two couple moments B) One force and two couple moments C) Three forces D) Three forces and one couple moment 30 2. A general system of forces and couple moments acting on a rigid body can be reduced to a A) single force B) single moment C) single force and two moments D) single force and a single moment 3. The three scalar equations, E Fx EFy E Mo 0, are equations of equilibrium in two dimensions. A) Incorrect B) The only correct C) The most used D) Not sufficient 4. The forces on the pole can be reduced to a single force and a single moment at point A) P B) Q C)R D) S E) Any of these points. y 5. If a support prevents translation of a body, then the support exerts a on the body. A) Couple moment B) Force C) Both A and B. D) None of the above

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please fast answer
Question 34 of 46 A man exerts a force Fon the handle of the stationary wheelbarrow at A. The weight of the wheelbarrow along with its load of dirt is 215 lb with center of gravity at G. For the configuration shown, what force F must the man apply at A to make the net moment about the tire contact point B equal to zero? Assume a = 43 in., b = 8 in., h = 22 in., 0 = 24°, and = 50°. %3D %3D W B. Answer: F = Ib
I have tried this using both scalar and vector form of moment notation. this should be a simple problem but I am not getting the right answer how do I solve this?
The three identical bars, each weighing 10.8 lb, are connected by the two freely pinned links of negligible weight and are resting on a smooth horizontal surface. Calculate the initial acceleration a of the center of the middle bar when the 7.8-lb force is applied to the connecting link as shown. 7.8 lb Answer: a = i ft/sec2
Draw the Normal Force (N), Shear Force (T) and Bending Moment (M) diagrams of the beam whose span and loading condition are given in the figure. H(t)2 M (tm)15 q1(t/m)16 q2(t/m) 19 P(ton)15 a(m)4
The Cantilever Beam Shown Below carries a distributed load and a point load. Determine the reactions of support A and B.
Please draw the complete free body diagram including the components. And give explanations for the correct Answer
PLEASE ANSWER ALL OF THIS QUESTION ASAP!!!
The figure below shows a moving vehicle represented by two moving loads. The two loads are x = 2 m apart and they are to pass across a simple beam of length L = 12 m. If P1 = 53 kN and P2 = 98 kN, how far will the car travel when the moment induced is maximum. Simply put, what is the distance D (m) when the moment is maximum? Initial position: P1 P2 Position at maximum moment: D P1 L P2
1 ft 3 ft B 3 ft 3 ft (-9002 + 800f + 1000k) Ib.ft 6 ft 3 ft E (-300î – 400ĵ + 100k) Ibs The applied force at point E and the applied couple moment at point D are shown in the figure. Complete/calculate the following: (Where applicable, express the results as the (x, y, z) components of a Cartesian vector) 1. Draw the free-body diagram (FBD), showing the appropriate reaction forces and/or moments at the supports. (You must show the reactions in their component form i.e. show RAx, MRAX etc. on the FBD). Note: The support at point A is not able to resist a moment about the 'X' axis but is able to resist a force in this direction. 2. The unit vector ÅBc 3. The position vector Tɛ/a 4. The position vector īB/a
The magnitudes of the two forces shown are P = 115 N and Q = 95 N. Determine the magnitude of the combined moment of P and Q about point O. P A 240 mm 40° 90 mm, *******