Q.3) A beam is loaded and supported as shown in figure below. 3,000 lb 800 lb/t A 8,000 lb-ft |C D E 5 ft 4 ft 7 ft 4 ft a) Calculate the support reactions. b) Write the expressions for shear-force and bending-moment for a beam section between points C and D, as a function of x measured from the left-end of the beam. c) Draw complete shear and bending moment diagrams for the beam with the aid of the areas of loading and shear-force diagrams. Be sure to label the values of shear force and bending moment on the diagram.

Q.3) A beam is loaded and supported as shown in figure below. 3,000 lb 800 lb/t A 8,000 lb-ft |C D E 5 ft 4 ft 7 ft 4 ft a) Calculate the support reactions. b) Write the expressions for shear-force and bending-moment for a beam section between points C and D, as a function of x measured from the left-end of the beam. c) Draw complete shear and bending moment diagrams for the beam with the aid of the areas of loading and shear-force diagrams. Be sure to label the values of shear force and bending moment on the diagram.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam shown, the magnitude of the concentrated load is P = 28 kN, the magnitude of the couple is MB = 230 kN·m, and the beam lengths are a = 5.8 m and b = 17.4 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Determine the internal shear force acting at point C Determine the internal moment acting at point C
Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P2 = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm² and Acp = 9,280 mm². The distances between various points on the bars are shown in the figure. Determine the vertical displacements &, and ôp of points A and D, respectively. E1.5m 1.5 m 2.1 m – A P = 400 kN 2.4 m P2 = 360 kN F 0.6 m|
Problem: Analyze the continuous beam shown in Figure by drawing the shear and bending moment diagram and sketch the elastic curve. 10 ft AB 1.2 k/ft 30 ft 60 k ↓ 20 ft 10 ft 40 k 15 ft 5 ft E
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
Consider a 200-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 70 kN-m and 74 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume bq = 155 mm, b2 = 30 mm, b3 = 245 mm, d1 = 65 mm, d2= 200 mm, d3 = 65 mm. Determine the maximum horizontal shear stress in this segment of the beam. b1 b2 d2 MA MB |dz A B b3 Ax Answer: Tmax = i MPa
For the beam shown, the magnitude of the concentrated load is P = 12 kN, the magnitude of the couple is MB = 150 kN·m, and the beam lengths are a = 4.7 m and b = 14.1 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Draw the shear force and bending moment diagrams for the beam shown in the figure below. 80 kip 3 kip/ft B 75 ft 50 ft 75 ft 225 ft 125 ft A = 103 kip B, = 408 kip Cy = 840 kip Dy = 15 kip
a) Calculate supportive reactions.b) Determine the shear equations, V(x), and the bending moment, M(x).c) Sketch the V and M diagrams for the beam. Consider H = 83.
Solve the intermediate beam shown on the page using the slope deflection matter. Draw the deflected shape, free body diagrams, and the bending movement diagram for the structure with the maximas, minimas, zeros and their locations
Calculate the shear force V and bending moment M at a cross section just to the left of the P, load acting on the simple beam AB shown in the figure. P = 1900 lb and P, = 600 lb. -30 in. 50 in. 40 in. 120 in. Round your answers to the nearest whole number. V = lb M = Ib - in.
1 ft 3 ft B 3 ft 3 ft (-9002 + 800f + 1000k) Ib.ft 6 ft 3 ft E (-300î – 400ĵ + 100k) Ibs The applied force at point E and the applied couple moment at point D are shown in the figure. Complete/calculate the following: (Where applicable, express the results as the (x, y, z) components of a Cartesian vector) 1. Draw the free-body diagram (FBD), showing the appropriate reaction forces and/or moments at the supports. (You must show the reactions in their component form i.e. show RAx, MRAX etc. on the FBD). Note: The support at point A is not able to resist a moment about the 'X' axis but is able to resist a force in this direction. 2. The unit vector ÅBc 3. The position vector Tɛ/a 4. The position vector īB/a