Q.1) A horizontal beam is loaded and supported as shown below. (a)Determine the support reactions at A. (b) Write expressions for the shear force and the bending moment as a function of x (where x is measured from point A) between points C and D. (c)Draw the shear force and bending moment diagrams for the entire beam with the aid of the areas of loading and shear-force diagrams. Be sure to label the values of shear force and bending moment on the diagram. 3 m 250 N/m 150 N/m 120 N.m B D E| - 2 m - 2 m- 2 m 500 N

Q.1) A horizontal beam is loaded and supported as shown below. (a)Determine the support reactions at A. (b) Write expressions for the shear force and the bending moment as a function of x (where x is measured from point A) between points C and D. (c)Draw the shear force and bending moment diagrams for the entire beam with the aid of the areas of loading and shear-force diagrams. Be sure to label the values of shear force and bending moment on the diagram. 3 m 250 N/m 150 N/m 120 N.m B D E| - 2 m - 2 m- 2 m 500 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam shown, the magnitude of the concentrated load is P = 27 kN, the magnitude of the couple is MB = 170 kN·m, and the beam lengths are a = 6.4 m and b = 19.2 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Q.2) (a) Calculate the support reactions of the loaded beam shown below. (b) Write equations for w(x), V(x) and M(x) of the beam using singularity functions. (c) Sketch the shear-force and bending moment diagrams for the beam for the beam using the Graphical method. Label the values of shear-force and bending-moment at all key points. 120N/m 300 N 300 N-m 200 N 100N/m Im B 4m C Im DIm E 4m 1m G 400 N¬m
For the beam shown, the magnitude of the concentrated load is P = 23 kN, the magnitude of the couple is MB = 350 kN·m, and the beam lengths are a = 7.2 m and b = 21.6 m.(a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A.(b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Part 1 Cut a cross-section through the beam at variable distance x, where 0 < x < a. Derive equations for the shear force V and…
Calculate the forces in all members using equilibrium of joint, ALso check weather the member is in tension or in compression. only HANDWRITTEN answer needed ( NOT TYPED)
Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P2 = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm² and Acp = 9,280 mm². The distances between various points on the bars are shown in the figure. Determine the vertical displacements &, and ôp of points A and D, respectively. E1.5m 1.5 m 2.1 m – A P = 400 kN 2.4 m P2 = 360 kN F 0.6 m|
Problem: Analyze the continuous beam shown in Figure by drawing the shear and bending moment diagram and sketch the elastic curve. 10 ft AB 1.2 k/ft 30 ft 60 k ↓ 20 ft 10 ft 40 k 15 ft 5 ft E
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
Learning Goal: A beam with length L = 2.9 m is supported by a pin joint at A and a cable attached at C as shown in (Figure 1). It is subjected to the distributed load with w₁ =1.7 kN/m and w₂ = 2.1 kN/m. The angle between the cable and the beam is 0 = 35°. Determine the normal force, shear force, and bending moment acting at point B, located x = 0.6 m to the left of the end of the beam. D Wi W2 C B L Begin by finding the support reactions for the beam using the free-body diagram shown in (Figure 2). What is the tension in the cable? Express your answer to three significant figures with appropriate units What is the horizontal reaction force at A? Assume the forces acts in the direction shown, and use an appropriate sign. Express your answer to three significant figures with appropriate units. What is the vertical reaction force at A? Express your answer to three significant figures with appropriate units. Now calculate the internal loading at point B using the free-body diagram of…
2.0 m ㅏ F 3.0 m q 4.0 m The above freely supported light uniform beam of length 10 m carries a point load F = 45 kN and a uniformly distributed load q = 23 kN m −1 at the positions indicated. Find the shear force V (x) and the bending moment M(x) at the following points along the beam. Give your answers correct to two significant figures. At the point x = 4 m the shear force and bending moment are: V(4) and M(4) = KN kN m. At the point x = : 8 m the shear force and bending moment are: KN = V(8) and M(8) = kN m 1.0 m + -+
For the beam shown, the magnitude of the concentrated load is P = 12 kN, the magnitude of the couple is MB = 150 kN·m, and the beam lengths are a = 4.7 m and b = 14.1 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
7. As shows in the picture, two circular rods have the same diameter, left rod made by steel, right rod made by aluminum, the ratio of shear modulus of two material is 1:3, the deformation of the curved arm at end of the two circular rod is not considered. Request: What proportion of force F will be allocated to the left and right two poles? St Al
For the beam and loading shown, (a) Use discontinuity functions to write the expression for w(x). Include the beam reactions in this expression. (b) Integrate w(x) twice to determine V(x) and M(x). (c) Use V(x) and M(x) to plot the shear-force and bending-moment diagrams. Let a = 5.0 m, b = 1.7 m, wA = 16 kN/m, and wB = 46 kN/m. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.