2.0 m ㅏ F 3.0 m q 4.0 m The above freely supported light uniform beam of length 10 m carries a point load F = 45 kN and a uniformly distributed load q = 23 kN m −1 at the positions indicated. Find the shear force V (x) and the bending moment M(x) at the following points along the beam. Give your answers correct to two significant figures. At the point x = 4 m the shear force and bending moment are: V(4) and M(4) = At the point x V(8) = and KN kN m. = 8 m the shear force and bending moment are: KN M(8) = kN m 1.0 m + トー

Q: Problem 2 -A concentrated couple, = 600 Nm acts at the center of the simply Supported beam which is…

A:

Q: per the attached figure:  a shear force of V = 448 kN is applied to the box girder. determine the…

A: A shear force of V =448 kN is applied to the box girder.Find the moment of inertia (I) of the box…

Q: For the beam shown, the magnitude of the distributed load is wo = 11.0 kN/m and the beam lengths are…

A:

Q: Consider the beam with an overhang shown in the figure. a. Determine the shear force V and bending…

A:

Q: Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude…

A:

Q: For the simply supported beam subjected to the loading shown, derive equations for the shear force V…

A:

Q: Vertical Reaction at C in kN. Moment Reaction at C in kN-m.

A:

Q: e) the value of the integration constant C2 f) the value of the integration constant C4. g) the…

A: Data given Find :  (a) the value of the integration constant C2 (b) the value of the integration…

Q: Evaluate the bending moment diagram for the continuous beam in Figure below using the flexibility…

A: To determine:Bending moment diagram

Q: The beam in Figure 2 is pin supported at A and roller supported at B. Calculate an equivalent…

A:

Q: A single-bay frame of the type illustrated in Figure 9.5 carries a horizontal load of 5000 lb acting…

A:

Q: For the beam shown, the magnitude of the distributed load is w0 = 10.2 kN/m and the beam lengths are…

A: Draw SFD and BMD?

Q: Upvote will be given. Please write the solutions legibly. Solve in 2 decimal places. 15 KN 20 KN/m…

A: A simply upported beam is loaded as followsmax shear force=?max bending moment =?

Q: loading w 1 The overhanging beam is supported at A and B and has a uniformly distributed 15.8 kN/m…

A: Maximum shear force can be determined from Shear force Diagram (SFD). Using method of section to…

Q: A 240mm diameter circular simply supported beam carries a concentrated load, uniformly distributed…

A: The question is based on the simply supported beam subjected to uniform, varying, and point load.…

Q: The beam shown in the figure is subjected to a moment of M = 50 kN.m. Determine the bending stress…

A: Bending stress at point A is given as  ; σA = M*yAIN-A M = Moment = 50 KNm = 50 * 106 yA = Distance…

Q: Use the graphical method to construct the shear force and bending moment diagrams for the beam…

A: Shear force and bending moment diagram

Q: The beam with cross-section shown in Figure 1 is subjected to a uniformly distributed load and a…

A: I = 2.18 x 106 mm4

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.