Q1: Based on the gear train given in below figure with 1000 rpm input speed, calculate the output rpm (rev/min)? (Input gear - 1 and output gear - 4). N, = 30 teeth N, = 55 teeth N = 55 teeth 2-3 N = 30 teeth 4. Compound gear 3 Input Output

Q1: Based on the gear train given in below figure with 1000 rpm input speed, calculate the output rpm (rev/min)? (Input gear - 1 and output gear - 4). N, = 30 teeth N, = 55 teeth N = 55 teeth 2-3 N = 30 teeth 4. Compound gear 3 Input Output

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An indexing mechanism of the milling machine uses a gear train shown in figure task 1d. The drive is from gear wheels A and B to the bevel gear wheel D. The following table shows the tooth number on each gear, solve using tabular method. How many revolutions does D makes for one revolution of A under the following situations: Tabular column (i) If A and B are having the same speed and same direction (ii) If A and B are having the same speed and opposite direction (iii) If A is making 80 rpm and B is at rest (iv) If A is making 80 rpm and B 40 rpm in the same direction. (v) Also define the term Speed ratio and train value Please with clear words
Need answer as well as soon Only typed answer needed Handwritten answer not allow There is a helical gear with a right angle module 3mm, a pressure angle of 20°, an inner width of 75 mm, a torsion angle of 25°, the number of pinion teeth 32, rotation angular speed 620rpm, and the number of teeth of the gear 75. If the material of the pinion and gear is SM25C (H b=150], what is the maximum transmission power?[Answer; 4.36 kw]
Industrial Maint. What are the direction and speed of the driver gear (D1) in Figure 6-40 if the driven gear (D2) is a 2 in. gear, D1 is a 12 in. gear and D2 is rotating at 1248 rpm (CW)? see picture
b) Figure Q1b shows a compound gear train with Gear A as the pinion (or driver) with an input Power (Pin) of 600 W at Gear A. If Gear A rotates at 139.70 rpm and engages with Gear B, calculate the angular velocity (w) in rad/s for Gears B, C & D; and the input torque (Tin) in at Gear A and output torque (Tout) at Gear D. The number of teeth (N) for gears A, B, C & D are 62 teeth, 34 teeth, 42 teeth and 22 teeth, respectively. Assume 100% efficiency and no frictional losses; and give your answers to two decimal places. GEAR A GEAR C GEAR B GEAR D
2. The following data is for the gear train shown in the figure: Given: N2 = 30t, N3 = 35t, N4 = 55t, N5 = 40t, N6 = 50t, N7 = 40t %3D w2 = 30 rpm ccw, warm = 20 rpm cw, Input torque on gear 2 is 1200 lbf.in Determine the following: a. Angular velocity of the sun gear. b. The gear ratio R required to determine the angular velocity of gear 6. c. The angular velocity of gear 6. d. The angular velocity of gear 7. e. Output torque on gear 7. Be careful with your units. Arm 6 ... 7
4- Find the gearing ratio for the given compound gears shown in figure 10. 5- Given that the torque (t) of the driver gear is (40+x) N.m, find the torque of the green gear. (x is the last digit of your ID) (M) rrrrv Figure 10 Figure 11 D Error
1. The figure below is a spur gear train drive and gear 2 is the inlet of the gear train. It transfers 12 kw of power at 1200 rpm. Gear 3 and 4 have 60 and 20 teeth respectively and are made with 20° pressure and full-depth teeth. The desired speed for the output shaft is 32 rpm. a. Find the minimum number tooth on gear 2 to obtain 32 rpm at the output and confirm its validation for interference-free power transfer. b. Find the speed ratio at each gear set using the results obtained at "a"(above). c. Determine the rotational speed of each gear (n2, n3, n4, and n5) using the results obtained at "a"(above). d. Find the torque of each shaft (Tin, Te, Tout) assuming that there is no frictional loss during the power transfer. e. Determine the radial, tangential and total forces transmitted at the last gear set assuming a module as m=4 mm, and draw the free body diagram of gear 4 showing the forces and torques. 75, 100 2007 In Out 4
A planetary gear train is shown in the figure. The sun gear (gear 1) is fixed, it has a 1-in. pitch diameter with a diametral pitch of 12. Gear 3 has 36 teeth and gear 4 has 20 teeth. Gear 5 has 40 teeth and is keyed to the same shaft as gear 4. Gear 5 mates with the ring gear (gear 6), which serves as the output from the train and has 160 teeth. The carrier (link 2) serves as the input to the train, determine the rotational velocity of the ring gear when the input shaft rotates at 1125 rpm clockwise.
Find the gear ratio of the given simple gear train? (see figure ) * 5 0.5 O 3 A 301 B 901 C By V. Ryan C 15T
4. What is the overall gear ratio for the following compound gear train? What is the output shaft speed and direction if the input shaft rotates clockwise at 1000 rpm? 8 teeth, Ø 5mm 16 teeth, Ø 10mm 24 teeth, Ø 15mm 32 teeth, Ø 20mm driver driven
Hello good Afternoon Sir, Permission, i have a question in my homework. The following bellow is question. Please advice. Thank you Regards,Irfan In planning the combined gears of the Ferguson planetary paradox as shown in the figure below.Sun gear hand input with angular speed (w2) = 0 rpm and hand input with angular speed (w.arm) = 400 rpm counterclockwise (ccw)Where is the number of teeth:Sun gear N2 = 100 (external gear)Sun gear N3 = 99 (external gear)Sun gear N4 = 101 (external gear)Planet gear N5 = 20 (external gear)Calculate the angular velocity, for each gear using the tabulation method. The data is in the image below
In the planetary gear train shown in below figure, Gear A is the driver and gears B and D are compounded.Gears E and C are internal gears with C as the fixed gear.Number of teeth on gears are TA-20;TB-60; Tc-140;TD-40;,TG-120. If the drive gears rotates at 720rpm CCW when seen from the right, find out the speed at which driven gear rotates C140 120 Output D 40 60 20 Input