Q1 a) For the following system: s+ 4 (s + 2)(s + 4) i) What are the poles and zeros of this system ii) With the aid of a sketch, comment on the stability of the system b) For the following system: 1 s3 + 12s2 + 20s i) Describe the system as state space in the standard matrix form

Q: Can you please create a subtraction circuit

A: Differential amplifier contains opamp can be used to create subtraction circuit.

Q: For the circuit shown in the following figure. The output voltage is equal to--. 5 kn 5 kn -1 Vo 5…

A:

Q: :) c 2 3 :00 8 to Find RCD

A:

Q: 2 kn +) 6 V 1 kn 2 mA 4 mA 12 V 2 kN 31 kN 1 kn 31 kn Vo ww

A: The solution is given below

Q: b) Design Synchronous counter to count the following sequence using T F/F: ► 1 – 7 – 4 – 3

A: SEQUENTIAL LOGIC CIRCUITS: Sequential Logic circuits, unlike Combinational Logic circuits, have some…

Q: Analyze the timing diagram.  Redraw so that you insert and enable the PRESET in the CLK cycle D-E on…

A: include a PRESET pulse inserted and enabled during the CLK cycle D-E on the rising edge.Original…

Q: 3) Draw the block diagram of the following schematic. Inside each block indicate which component it…

A: Given information The given schematic contains an input voltage that varies depending on the speed…

Q: 2 Perform subtraction on the following numbers using 2's complement 01001-01010

A:

Q: The O proportional O integral O derivative mode eliminates steady-state error.

A: The above questions are based on the effect of various controllers in a standard process control…

Q: Obtain a the system TF for SFG diagram MO 332 be $0.

A: In this question We need to determine the transfer function using the signal flow graph.  C/R = Pi…

Q: Which one of the following is the correct implementation of this multiplexer?

A:

Q: Calculate the energy in each of the signals (a) x(n) = u(n) - u(n − 3) - (b) x(n) =…

A:

Q: The step size of a 5-level midtread quantizer is delta=2V and the input is 3.2V. Determine the…

A: Quantizing an analog signal value is done by dividing the signal by several levels of measurement.…

Q: A function appears in thefom using CswatandSinWmtas.inputs. áa black diagrams, Show haw…

A: Given :fck=cos ωct-ksin ωmt sin ωct   coswct→-90 phase shifter→sinwct

Q: Use 8x1 multiplexer to A'C' + BC + AC

A: Given:A boolean expression, F=A'C' + BC + AC,we need to implement: above boolean function using 8:1…

Q: *2. Find the convolution of the following two signals manually (using graphical sketch and…

A:

Q: a A. 196

A:

Q: are slower than combinational circuit Sequntional circuit O PROM O Synchronous circuit O

A:

Q: can someone do d-g?

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Above is a sinusoidal voltage (x-axis shows time in seconds, y-axis voltage in volts). Using the…

A: Here we have find the timeperiod, frequency and angular frequency,amplitudes.

Q: A counter circuit is shown in the figure. The counter counts as QO Q1 Clock K K

A:

Q: 231460nsiden the signal xcH that shamunbelow sketchi cazt)

A:

Q: Two poles & tvo zeros Design the filt er Fs = 8000 Hz 1500 2000 400

A: According to the question, we need to design a filter by using the given pole-zero plot

Q: Simplify BC + B(A+B) + B(A+C) Answer = a. A+BC O b. B+AC O c. A O d. B

A: In this question we need to simplify the given Boolean algebra.

Q: IN class A chopper, if the inductance is increased, then the output voltage will be smoothed the…

A: In class A chopper load is current is same as inductor current.

Q: what are the structural differences between reverberating and converging circuits

A: The converging circuit: The converging circuit diagram is shown in the following figure:

Q: The Star Connection Recap

A: Star connection: In the Star Connection, the similar ends of the three windings are connected to a…

Q: Question Bulding with Full adder using Magnitude Comparator

A:

Q: Input Biáš čurrnent = 30URA Hint Slides 99-104 of Lecture 5 Noninverting input U1 R3 Output OPAMP 3T…

A:

Q: signal systems the input is unit step signal function

A: To solve this problem, we need to determine the output signal   y(t)   of the two parallel LTI…

Q: QUESTION 5 Analog output modules are used to simply set an output either on or off O True False

A: Given, Statement is  A statement about the output of the analog signal is given. To find out We need…

Q: Draw the Vs and is as a function of time when the switch on at t=0 R3 S2 ↑ Vs Rr=0⁰ Ro E к

A: As it is purely resistive Circuit and it is opened at the end then no current will flow and there…

Q: onvert the ollowing mnemonic program ladder diagra LD 0.00 AND NOT 0.01 LD 1.00 AND 1.01 20.00 20.01…

A: To convert the given mnemonics program into ladder diagram

Q: TRANSCRIBE THE FOLLOWING SOLUTION IN DIGITAL FORMAT

A: The input supply voltage is .The capacitance values are,,,The inductance value is .

Q: A complete subtractor circuit designed using 1-Mux 4-to and for ABB selectors the input value of the…

A: A Multiplexer is an electronic device which have multiple input terminals and only a single(or less…

Q: When Select-0, the output of the array will be D3 D2 D1 DO Select

A: Given: simple circuit

Q: Time taken for the response to raise from * 10 to 100 % is Setting time O Peak time O Delay time O…

A: Time taken for the response to raise from 10 to 100 % is  A. Setting time  B. Peak time  C. Delay…