Q1// A double-cage of a 3-phase, 50-Hz, 4-pole induction motor, have the followingequivalent circuit parameters, all of which are phase values referred to the stator and thestator impedance is negligible:Outer cage Ro' = 9 NInner cage R;' = 2 N1- Calculate the ratio of torques produced by outer cage and inner cage at starting.2- If the motor runs at 1425 rpm and the rotor input phase voltage is 230 V, calculate theXo' = 2 QX;' = 8 Ntoque in synchronous watt per phase3- What slip will the torque contributed by the two cages be equal?

Frequency (f) = 50 Hz No. of poles (P) = 4 Resistance of the outer cage referred to stator (Ro') = 9…

Q1// A double-cage of a 3-phase, 50-Hz, 4-pole induction motor, have the following equivalent circuit parameters, all of which are phase values referred to the stator and the stator impedance is negligible: Outer cage Ro'= 9 N Inner cage R;' = 2 Q 1- Calculate the ratio of torques produced by outer cage and inner cage at starting. 2- If the motor runs at 1425 rpm and the rotor input phase voltage is 230 V, calculate the toque in synchronous watt per phase 3- What slip will the torque contributed by the two cages be equal? Xo' = 2 Q X;' = 8 Q

Q1// A double-cage of a 3-phase, 50-Hz, 4-pole induction motor, have the following equivalent circuit parameters, all of which are phase values referred to the stator and the stator impedance is negligible: Outer cage Ro'= 9 N Inner cage R;' = 2 Q 1- Calculate the ratio of torques produced by outer cage and inner cage at starting. 2- If the motor runs at 1425 rpm and the rotor input phase voltage is 230 V, calculate the toque in synchronous watt per phase 3- What slip will the torque contributed by the two cages be equal? Xo' = 2 Q X;' = 8 Q

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three-phase, 460-V, 60-Hz, four-pole Y-connected induction motor has the following equivalent circuit parameters: Rs = 0.42Ω, Rrʹ = 0.23Ω, Xs = Xrʹ = 0.82Ω, and Xm = 22Ω. The no-load loss 60W, may be assumed constant. The rotor speed is 1750 rpm. The rotational losses at this speed is 500W. Use the approximate equivalent circuit in figure below, to determine (a) the synchronous speed Ns; (b) the slip s; (c) the input current Ii; (d) the input power Pi; (e) the input PF of the supply, PFs; (f) the gap power Pg; (g) the rotor copper loss Pru; (h) the stator copper loss Psu; (i) the developed torque Td; (j) the efficiency; (k) the starting current Irs and starting torque Ts; (l) the slip for maximum torque sm; (m) the maximum developed torque in motoring, Tmm
The rotor of a four-pole, 50 Hz slip-ring induction motor has a resistance of 0.2 0 per phase and runs at 1425 rpm at full-load. Determine the external resistance per phase which must be added to reduce the speed to 1200 rpm, the torque remaining same in both the cases.
A 3 phase , 6 pole , 400 V , 50 Hz , induction motor has R2= 0.1 ohm /ph , X2= 0.8 ohm /ph and the induced emf between slip rings at standstill is 160 V , Assume the friction losses is 300 W. find :- a) the torque output at slip =3% . b) critical slip and the torque maximum .
Example -6. A three-phase, 60-Hz, four-pole induction motor runs at a no-load speed of 1790 r/min and a full-load speed of 1720 r/min. Calculate the slip and the 8 |Page electrical frequency of the rotor at no-load and full-load conditions. What is the speed regulation of this motor?
g) What is an advantage if the starting Torque of the induction motor is higher than the nominal load Torque? h) What are the main differences when the equivalent circuits of transformer and asynchronous motor are examined?
7. The total rotational losses of an induction motor are a combination of ------- A) Friction losses B) Windage losses. D) Stray losses. C) Core losses. 8. The developed mechanical power can be calculated using the equation of- A) PAG - PRCL. B) PAG w sync C) (1-s) PAG. D) 3 E2Gc. 9. For an induction motor, if the synchronous speed is 1800 r/m, and the rotor speed 180rad/sec, then the slip will be: A) 5.5% C) 6% B) 4.5% D) 4% 10. The power losses in the stator part of the induction motor are B) Core losses D) Friction and windage losses A) Stator copper losses C) Air-gap losses
A 460 V, 60 Hz, Star connected, 870 r.p.m., Eight poles, Three-Phase Induction Motor has the following per phase parameters: R1 = 0.07, R2 = 0.05, X1 = X2 = 0.2, Xm = 6.5, Draw the approximate equivalent circuit and determine the following:I. Starting TorqueII. Maximum TorqueIII. Rated TorqueIV. Stator CurrentV. Power FactorVI. Input PowerVII. Magnetizing Current
3. A 440V 60-hp six pole 60 hz A connected induction motor has the following parameters R1=0.048 R2= 0.035 Xm= 9.50 X1= 0.33 0 X2= 0.37 0 Pcore= 600W PF&W= 350W Use the Thevenin's Equivalent circuit concept to find: (a)Vth and Zth seen by the rotor circuit (b)The slip at which maximum torque occurs (c) the value of Max/pullout Torques (d) The starting torque.
Q1: Fill in the following blanks: 1. In order to have sparkless commutation, the brushes should be placed along... 2. D.C. series motor are used in those applications where... required. 3. The self-induction of a coil undergoing commutation causes .. . at the brushes. .starting torque is
The equivalent circuit parameters of a 230-V, 1-phase, 6-pole, 60-Hz induction motor are: R1 = R2’ =10ohm, X1 = X2’ = 10ohm, and Xm = 100ohm. At a slip of 5%, calculate the developed torque and The input power to the motor at 230V, while running on no-load, is 31.4 W at 1.2 A. What is the approximate efficiency of the motor at 5% slip?