Q1- A boiler generates 500 kg/h of steam at 16 bar and 300C from feed water at 30°C. Coal used is 60 kg/h of C.V 30000 kJ/kg. Find equivalent of evaporation and boiler efficiency. Ans(10.75 kg/kgf 80.9%) Q2// For simple Rankine cycle, the steam used by the turbine is 5.4 kg/kWh at a pressure of 50 bar and a temperature of 350°C. The efficiency of the boiler is 82% with feed water at 150 °C. a- How many kg of coal are required per kWh? The Calorific value of fuel is 28100kJ/kg. b-if the cost of coal is 10S per ton, then what is the fuel cost per kWh. Ans(82%, 5.72E-3)

Q1- A boiler generates 500 kg/h of steam at 16 bar and 300C from feed water at 30°C. Coal used is 60 kg/h of C.V 30000 kJ/kg. Find equivalent of evaporation and boiler efficiency. Ans(10.75 kg/kgf 80.9%) Q2// For simple Rankine cycle, the steam used by the turbine is 5.4 kg/kWh at a pressure of 50 bar and a temperature of 350°C. The efficiency of the boiler is 82% with feed water at 150 °C. a- How many kg of coal are required per kWh? The Calorific value of fuel is 28100kJ/kg. b-if the cost of coal is 10S per ton, then what is the fuel cost per kWh. Ans(82%, 5.72E-3)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. In a steam power cycle, steam enters the turbine at 30bar with the following different conditions and leaves at 1bar. Calculate Carnot efficiency, Rankine efficiency, condenser heat flow in kW assuming mass flow rate of steam as 9.5kg/s and steam rate for each case considering the pump work. (ii)Wet with 0.95 dryness (iii) Superheat at 550°C
1. In a steam power cycle, steam enters the turbine at 30bar with the following different conditions and leaves at 1bar. Calculate Carnot efficiency, Rankine efficiency, condenser heat flow in kW assuming mass flow rate of steam as 9.5kg/s and steam rate for each case considering the pump work. Using mollier diagram (ii)Wet with 0.95 dryness
3- Air enters the compressor of a gas turbine at 120 kPa, 310 K. The air compressed to 1100 kPa, the turbine inlet temperature is 1460 K and the expansion occurs in two stages, with reheat to 1420 K between the stages at a pressure of 300 kPa. The compressor efficiency is 85 %. The net power developed is 2.2 MW. sketch T -S diagram then Determine: The thermal efficiency of the cycle. Qin Qin The back work ratio. Combustor Reheat combustor Turbine Turbine stage 1 stage 2 cycle Compressor
1. Figure shows a reheat cycle in which steam is delivered to the high-pressure turbine at 1100 Ibf/in^2, 740 F, and expanded to 200 Ibf/in^2. After the expansion, the steam is warmed to 720 F before being expanded to 1 lbf/in^2 in the low- pressure turbine. Assume the turbines and pump are adiabatic. Compute the high pressure isentropic turbine work. High Q'în Boi ler Condenser Pump Q out 166.8 Btu/lbm 200.1 Btu/lbm 190.2 Btu/lbm 231.1 Btu/lbm 120.5 Btu/lbm
Problem (1.2) A steam power plant working according to simple Rankine cycle. It has a high pressure of 3 MPa and it maintains 60°C in the condenser. A condensing turbine is used, but the quality should not be lower than 90% at any state in the turbine. Find the cycle efficiency. [reference: Fundamentals of Thermodynamics by Borgnakke & Sonntag prob.11.18,p-460].(Ans.33.2 %).
for a rankine cycle, steam at 5.25 MPa. 435 degree celcius expands to 0.036 MPa. For 10kg/s of steam, determine heat added, heat rejected, work of turbine, thermal efficiency
1. A reversible Carnot engine has a hot reservoir at T=880K and a cold reservoir at T=340K. The working gas (1mole) has a heat capacity Cv,m=5R/2. - Draw the cycle on a PV plot, marking the temperatures at each point a, b, c and d. The volumes are Va=4L, Vb=15L, Vc=32L and Vd=7L. - State for each path a -> b, b -> c, c-> d, d -> a, whether process is adiabatic, isotopic, isothermal, and/or isobaric, and whether it's an expansion or a compression. - Calculate the work and q (heat) associated with each path. - What is the efficiency of this engine? Thanks a lot.
A steam power plant operating on iregenerative cylce includes one feedwater heater [back word]. steam enters the turbine at 4500KPA and 500C and extracted from the turbine at 350KPA. what is thermal efficiency of the cycle ? TTD = 5
A 300 MW steam power plant, according to the simple ideal Rankine cycle references Water vapor enters the turbine at a pressure of 10 MPa and a temperature of 500°C; 10 KPA expands to condenser pressure.Isanthropic of turbine and pumpaccording to the efficiency of 85%, the degree of dryness of steam at the turbine output, find the thermal efficiency of the cycle and the mass flow of water vapor circulating in the cycle.
A four-cylinder compression-ignition engine with a compression ratio of 18 haspistons with a bore of 9 cm and a stroke of 10 cm. The air pressure at the beginning ofcompression is 98 kPaa, and the temperature is 37 oC. The engine may be modeled bythe air-standard Diesel cycle. The maximum cycle temperature is 1700 oK. If the engineproduces 75 kW of power, determine a) the heat supplied per cylinder; b) the thermalefficiency; and c) the rpm required.
A simple Rankine cycle works between pressures of 28 bar and 0.06 bar. The initial condition of the steamit is saturated. Calculate: a. Efficiency of the cycle b. Ratio of net work to the work of theturbine c. Specific consumption of steam in kg/kWh
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 4. Calculate the total turbine work of the cycle.