Why for b) the Vry is to the phase 30 degrees. Q1(a)An industrial unit operating at rated power can be represented by a balanceddelta connected load (ZRY etc) of (600 + j120) N and is connected to a 3-phase, 11 kV and 50 Hz supply.フDraw the circuit diagram, indicating VRY, the yellow line current (IR) and theload phase current (IBr ).lineVoltayCalculate:(i)The three load phase currents (IRY, IYB and Ibr).(ii)The three line currents (IR, Iy and IB).(iii)The total real power, apparent power, reactive power andpower factor at the 3 phase supply.An unbalanced condition in the above load in Q1(a) causes the impedanceof ZRY to reduce to (450+j40) N, ZyB to reduce to (500 +j100) Q. and ZBr toremain the same.b2/2ncedtar(i)mer BUsing the information above:Calculate the 3 load phase currents (IRY, IYB and IBR).(ii)Draw a scaled phasor diagram indicating all phase and linevoltages, and the three load phase currents.(iii)Using the scaled phasor diagram or otherwise determine thethree line currents (IR, Iy and IB).(c)A 2 wattmeter measurement is made on the circuit in Q1(b). Wattmeter 1bases its measurements on VRY and IR, and Wattmeter 2 uses VBY and IB.Determine the power (W) measured by each wattmeter, and the resultanttotal 3 phase power. Confirm this measurement using any other suitablecaleulation.oba se pou

In this question we will write about line voltage phase.....

Q1 (a) An industrial unit operating at rated power can be represented by a balanc- delta connected load (ZRY etc) of (600 + j120) N and is connected to a phase, 11 kV and 50 Hz supply. line Draw the circuit diagram, indicating VRY, the yellow line current (Ir) and load phase current (IBR ). Volt2g Calculate: (i) The three load phase currents (IRY, IYB and IBR). (ii) The three line currents (IR, Iy and IB). (iii) The total real power, apparent power, reactive power ar power factor at the 3 phase supply. (b) of ZRY to reduce to (450+j40) N, ZYB to reduce to (500 +j100) Q. a remain the same. An unbalanced condition in the above load in Q1(a) causes the in mes 3 b2l2nced Using the information above:

Q1 (a) An industrial unit operating at rated power can be represented by a balanc- delta connected load (ZRY etc) of (600 + j120) N and is connected to a phase, 11 kV and 50 Hz supply. line Draw the circuit diagram, indicating VRY, the yellow line current (Ir) and load phase current (IBR ). Volt2g Calculate: (i) The three load phase currents (IRY, IYB and IBR). (ii) The three line currents (IR, Iy and IB). (iii) The total real power, apparent power, reactive power ar power factor at the 3 phase supply. (b) of ZRY to reduce to (450+j40) N, ZYB to reduce to (500 +j100) Q. a remain the same. An unbalanced condition in the above load in Q1(a) causes the in mes 3 b2l2nced Using the information above:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

in three phase it has been found that a negative sequence and zero sequence are absent what do you conclude from it?
Sum of scattering angles in Laboratory coordinate system is always equal to * O 2n None of them О п/2
a) Determine ?? ??⃗ and ?? ??⃗ using CDR. b) Sketch the phasor diagram for the currents.
This is a comparison between lab and wave , please add confirmation and arrange it more orderly,
D. Use this graphic for question 12 90° 180° |2 0° 270°
Determine the amplitude and phase shift of the sinusoidal ouput of the circuit shown below, if a sinusoidal input of frequency 80 rads/second and amplitude 5 volts is applied to the circuit. Add the phase shift to the amplitude and enter the result in the answer field (numerical answer only). Component values are R = 9860 Ohms;L = 0.00016 Henrys; Vin elle A R Vout
Impedances Z1 = 5.83 at angle of -59 deg. and Z2 = 8.94 at an angle of 63.43 deg. are in series and carry an effective current of 5A. Determine the Power and power factor of the circuit indicating if it is leading or lagging.
Please find Preal, Ptotal, and Pvar
Draw an RLC parallel circuit and draw current triangle (using phasor represantations) if source phase is 0 degree and the source current is leading source voltage 30 degrees. draw voltage and current phasor diagram for circuit.