Q.(d) A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal to 40 mm and 60 mm.What is the approximate largest torque that can be applied to the shaft if the shearing stress is not to exceed 120 MPa?

Q: 10. Figure 9 shows a system in which water flows from a tank through a pipe system having a several…

A:

Q: Whatis he length of a 2 ine given a scale of 1:40?

A: Given: The measured length of the line is 2”. The scale is 1:40.

Q: Draw the projections (Top, Front, Side) with Dimensions for this objects

A:

Q: Sketch SFD and BMD in terms of w and P

A:

Q: F & H are incorrect

A: As per question requirment we only find out f and h here. Find out -  (f) Length of Curve (h)…

Q: Define Peclet number.

A: It is defined as the ratio of the rate of advection of a physical quantity by the flow to the rate…

Q: Determine the following reactions

A:

Q: Define Full for of "BREEAM"

A: BREEAM: BREEAM stands for Building Research Establishment Environmental Assessment Method. It is…

Q: What is PD 1594. Explain

A: Introduction:- PD 1594 (PRESIDENTIAL DECREE No. 1594) Prescribing polices, Guidelines, Rules and…

Q: Find KN derivation Y = K m²³

A: We have to prove that the unit of unit weight is kN/m3.

Q: Find the area of each. Then put in square feet and square yards

A: 18.19.20.21.22.

Q: 2 10 10 Hol 10 10 Stable or instable?

A:

Q: 1⁄6 yard +3⁄8 yard

A:

Q: What is Finitely loaded area ?

A: Brief concept- The concept of finitely loaded area is related with the stress distribution in the…

Q: Renolds number, define it?

A:

Q: What exactly is a CompactFlash (CF) card?

A: A Compact Flash card (CF card) is a memory card format that was developed by SanDisk company in the…

Q: What is ponit of view? What is first point of view and third point of view.

A: The term  Point of view will be referred to who is telling or narrating the story. A story can be…

Q: According to this figure, What is d? What is dt?

A: Draw the figure.

Q: why divide x' in 2 in above method?

A: ##Calculation of location of x at such that due to given loading a  Maximum BM occurs ### As ask…

Q: what are the USCS group name for each of the four gradations

A: Given: Specimen LL PL PI Cc Cu 1 53 24 29     2       1.05 95.52 3 27 16 11 3.06 28.34 4…

Q: BEAUTIFUL 01/ Construct Polynomial Forth function gases in cas, within [0, 1]ns4

A:

Q: wrong given, pls. answer

A: Given: Span= 10m, axle loads as shown in figure

Q: 1) Determine the area of the shape below. -130.0- 100.0 -160.0-

A: The above figure is the trapezoid  The area of the trapezoid = sum of the parallel…

Q: why 3.5 instead of 2.5?

A: Correct solution is provided below

Q: You are appointed as an officer of Occupational Safety to investigate the incident happened during…

A: Officer of Occupational Safety is responsible for 1) Enforcing safety policies, 2) Conducting audits…

Q: Fullform of  PVDF

A: PVDF: Polyvinyl fluoride.

Q: 205, 406 ton=722 %3D How are Yoll tonne - 72 %31

A: Give that, Tonne is metric measure  1 TON  = 0.90718 tonne   TON is American unit

Q: Compute for the latitude of Line 1-2 A +4.81 B) +5.79 +8.03 D -18.63 Question 11 Compute for the…

A: Data is as given

Q: Find the area of each. Then put in square feet and square yards

A: Explanation(') means foot(") means inches1 square foot = 0.111 square yard1) Area of red rectangle =…

Q: Describe the structure of the surveyor’s compass.

A: The large surface when undulated the process used for surveying is known as surveyor's compass.

Q: The elevation of the following figure is one of the options O a Od O C O b Hedi b a C

A: Given data:

Q: Define Alidade.

A: Draw the figure.

Q: What are the two types of waiver's of lien?

A: The waiver of lien is a document from which is signed by a material supplier, subcontractor,…

Q: Explnation of EPDM.

A: The ethylene propylene diene monomer is abbreviated as EPDM.

Q: Difference betwen Veletile nd frzcead Saled

A:

Q: ISO 55000 is an international standard that provides governance for asset management. True False

A: Answer: True

Q: express each measurement in inches.41⁄2 feet

A: GIVEN :- Measurement = 412 feet To Determine :- Convert the given measurement into inches.

Q: Beginning ^ 2 3 4 LO 5 CO 9 8 7 3 10 10 11 12. 13 5 14 15 Identify the full name and abbreviation of…

A: To Determine: Full name and abbreviation of 8 10 15

Q: what about CB, IH, AB & AB

A: To find zero force members.

Q: Comparison between Davis, Penck, King's model.

A: