Q.4 If wo = 106 rad/s, Qf = 5 x 102 and m = 10-10kg, calculate the stiffness, and resistive constant of the system.
Q: The ratio of the tensile (or compressive) strength to the density of a material is a measure of how…
A: The objective of the question is to calculate the ratio of the tensile strength to the density of…
Q: 1. Posh a 25 box across floor at constat speed of lmb. MK 0,2 How much force do you exert on the…
A: Since you have asked multiple questions, we will solve the first question for you. If you want a…
Q: A body of mass 500 kg is suspended on the free end of an iron wire of length 3 m and cross-sectional…
A:
Q: In uniaxial loading the poisson's ratio is 0.30 and the strain in the x- direction is 250 x 10^-6.…
A: Given data μ=0.3εx=250×10-6 Here, μ is the possion's ratio. While εx is the strain in X direction.…
Q: 1. A frame ABC shown in Figure 2 consists of a tension member AB and a compression member BC. Member…
A: Given that Mdulus of elasticity,E=200 GPa=200×109Pa Horizontal force,H=150 kN=150×103N Length,L=3.5…
Q: QI/ The table below shows the values of stress amplitude and life cycles : Fatigue strength SE (Mpa)…
A:
Q: A fireworks show is choreographed to have two shells cross paths at a height of 107 feet and explode…
A:
Q: loads of PD = 145 kN & PL = 200 kN, and service moments of MDy = 35 kN-m & MLy = 60 kN-m. If Cb =…
A: Given as, W-shape for the beam is W12×65 Unbraced length L = 5 m Concentrated dead load (Tensile…
Q: nd trim printed circuit sheets. For the position shown, determine the vertical component of the…
A: Px = 390 sin 13 = 87.73 NPy =390 cos 13 = 380 N(FBD)x =2510034 FBD(FBD)y =9710034FBD
Q: Two parallel wires A and B are fixed to rigid support at the upper ends and subjected to same load…
A:
Q: An eccentric cam has diameter of disc 80 mm and an offset 30 mm from centre of rotation, operates a…
A: Given data: e= 80 mm=0.08 mMass of follower, m=2.5 kgStiffness of spring, k=4 N/mm =4×103…
Q: A mass spectrometer is a device that can sort ions based on their mass to charge ratio. incoming…
A: When the proton enters the magnetic field, the magnetic force on the proton will be equal to the…
Q: Each of the 16 fiber in the shown bundle has a linear density of1.9den. All bundled fibers are…
A:
Q: 5SON/m 30 17g 03
A: Given: The spring constant is k=550 Nm. The coefficient of friction is μ=0.3. The mass of the block…
Q: Determine what should be the magnitude of P and F to keep the concurrent force system in…
A: If a system of three concurrent and coplanar forces is in equilibrium, then Lami's theorem states…
Q: W В 270 mm A 180 mm
A: to keep the weight W balanced we should make sure that the forces from all directions must be…
Q: D = 0.4 mm diameter and I = 1 m long molybdenum wire is lengthened by force F = 41 N for Al = 1 mm.…
A: Dear student The Young modulus is defined as : Y = Stress / Strain Here, Stress = Force / Area…
Q: Drawa FBD of node B and using jolent method at B determine the forces in members BA and Bc. Note…
A: Answer..
Q: A two-cell tube has an outer wall of thickness "2t" and an inner wall of thickness "t". If the…
A: To answer: The torsional stiffness and the shear flows.
Q: A circular steel wire 2.00 m long must stretch no more than 0.25 cm when a tensile force of 890 N is…
A:
Q: A fiberglass composite consists of epoxy matrix reinforced with randomly oriented and uniformly…
A: Solution: As per the given data,
Q: Consider a metal bar of length L, cross-sectional area A, and Young's modulus Y. When a tension…
A:
Q: excitation is increased by 20% Jor Me suml ) Find the P, Q, E und s of the given system when…
A:
Q: Find the modulus of elasticity of a brass rod of cross section 20 mm x 20 mm, and length 248 mm…
A: Tensile load(T)= 50 KN Elongation (e)= 0.25 mm = 2.5× 10-⁴ m Length of the rod(L)= 248 mm= 0.248 m…
Q: Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces…
A: The area of triangle 1, A1=12×430×250+160A1=88150mm2 The area of triangle 2,…
Q: Take F = 250 N and d = 1.0 m (Figure 1). Figure 1.5 m B SC <1 of 1 Determine the force in cable AC…
A: See below
Q: tensile test
A: Tensile test is used to see stress upon material.
Q: ) What is luminescence? Briefly discuss the mechanism of LED with a neat sketch.
A:
Step by step
Solved in 3 steps with 3 images