Q.3. The right-angle bar shown in figure (3) is supported by a pin at B and a roller at C. What is the maximum value of the load P that can be applied if the ultimate shear strength of the pin is 30000 psí? The 3/4 inch diameter pin is in double shear. Use factor of safety = 1.5.

Q.3. The right-angle bar shown in figure (3) is supported by a pin at B and a roller at C. What is the maximum value of the load P that can be applied if the ultimate shear strength of the pin is 30000 psí? The 3/4 inch diameter pin is in double shear. Use factor of safety = 1.5.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The round shaft shown below is subjected to an axial impact/shock direct tensile load of F = 50000…

A: It is given that the stress at groove and the hollow part is equal, thus we will first look at the…

Q: The L-bar shown in the figure is fastened by a bearing at point A that allows it to rotate, such…

A: Given F=800NRBmax=600N

Q: Figure 2 shows a horizontal beam AB. It is pin-supported at end A and carrying a load Q at end B.…

Q: E

A: the area is 1 m^2 hence the power in watts will be 1270 W.

Q: Figure In the figure shown, a bar ABC with negligible mass carries a 20 kN load and is supported by…

A: the allowable shear stress of the pin in not given to get the diameter of the pin.please put the…

Q: The box beam shown in Figure P8.63b has dimensions of b=80mm, d=120mm, and t=8mm. A downward…

Q: 4. Solve problem 8.10 in our textbook (find the safety factor for failure at the fillet). Note that…

Q: Figure 2 shows a horizontal beam AB. It is pin-supported at end A and carrying a load Q at end B.…

Q: The assembly shown in the figure below consists of two sections of galvanized steel pipe connected…

Q: An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a load P at A,…

A: Calculate the reaction force as follows. Here, the tension in the wire CD is T.

Q: 5. The position of the rod DE is controlled by the hydraulic cylinder CF. For example, if the…

A: Given Load, P = 400 lb Bending stress = 15 ksi Diameter, d = 1/4 inch = 0.25 inch…

Q: The solid shaft shown in the figure below is fixed at one end and has a lever at the other. The…

Q: Link 3 shown acts as a brace to support the 270-lb load. For buckling in the plane of the figure,…

Q: calculate the maximal force F which can be applied to the couplin

A: fot solution refer below images.

Q: 5. The equilateral triangular tórsión member has sides equai lU D thickness t (Figure a). Figure b…

A: TMAX=100mpaG=70×103 mpab=16cmt=1cmTJ=ζr=GθLwhere θ and L consider as 1

Q: Q3) A short stepped bar is shown in Figure below. The stiffness of the large section is 12 kN/mm and…

A: Given data: k1=12 kN/mmk2=8 kN/mmF=6 kN Need to determine the displacement of the nodes 2 and 3.

Q: Solve the problem

A: Step 1: Step 2: Step 3: Step 4:

Q: The figure depicts a filleted cantilever bar. Find the largest normal stress for two cases: (a) the…

A: Given data: P=400 NM=10 N.mb=12 mm Need to determine the largest normal stress.

Q: 03: For the cyclic stress shown in the figure (aside) calculate: 1. The mean stress 2. The range of…

Q: 2. The link truss shown in the Figure is supported by a rocker at E & a hinge connection at A. The…

A: Given data: The value of the external load applied F = 4 kN = 4000 N The allowable shear of the…

Q: Question Completion Status: QUESTION 8 Consider the circular bent rod with diameter 20 mm. The…

A: We have to determine shear stress

Q: how many times is the system

A: For solution refer below images.

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: EXAMPLE: 4. A 2-in.-diameter steel tube with a wall thickness of 0.05 inch just fits in a rigid…

Q: The Uniform AB brass bar is fixed with support and pin as shown in the figure and has a rectangular…

A: Given data: (a) Write the expression for the critical load in the horizontal direction.

Q: The structure shown in the figure below consists of steel members connected via pins and is…

Q: Question 2) In the system given in the figure, a distributed load of w = 88 kN /m affects the AB rcd…

A: Given: load w= 88 kN/m; AB=4.1m; θ=56°; a=28mm;σm=212 MPa; ζm=70 MPa To Find: b? pin diameter at B

Q: A flat bar with a hole (see figure) has widths b = 60 mm and c = 40 mm. The fillets have radii equal…

A: b = 60 mm c = 40 mm R = 5 mm to determine diameter dmax of the largest hole

Q: Problem 4-21: The rigid beam is supported at its ends by two A- 36 steel tie rods. If the allowable…

A: Given:The allowable stress of the steel, The load, The value of The length of the rods,

Q: PROBLEMS Figure 1. In the figure shown, a bar ABC with negligible mass carries a 20 kN load and is…

A: Draw FBD

Q: The metallic hollow pipe shown in Figure Q1 is fixed at both its ends, and is under axial…

Q: Problem 4. The 16 × 22 × 100-mm rubber blocks (E = 54.76 MPa and v = 0.48) shown in the figure are…

A: Given: Length of the rubber block→L=100 mm Height of the rubber block→H=22 mm Allowable shear…

Q: The A frame shown in the figure is attached to an overhead beam by 2 cap screws, each of which can…

A: To determine the appropriate screw for the given load and conditions, we need to follow several…

Q: In the clevis shown in Fig. 1-11b, the minimum bolt diameter (d=22mm) and the minimum thickness of…

A: Given data Diameter = 22 mm Thickness = 10 mm Shear stress = 83 MPa Bearing stress = 138MPa Find…

Q: A frame is given above and an external load R is applied at point C. Pin connection at D is in…

A: Given data: External load R=45 kN applied at 'C'. Diameter of pins 'B' and 'D': dB=13 mm ; dD=8 mm.…

Q: 1. In the figure shown, a bar ABC with negligible mass carries a 20 kN load and is supported by pin…

Q: load of F=1433 kgf will be hung on a Workshop crane as in the figure. The pole to be used has a…

Q: Calculate the shearing stress in pin A of the bulldozer if the total forces acting on the blade are…

A: Two forces acting on the blade is 8K and 4K We can find the shear stress in each pin

Q: Q3) A short stepped bar is shown in rigure below. The stiffness of the large section is 12 kN/mm and…

A: Given data: k1=12 kN/mk2=8 kN/mF=6kN Need to determine the displacements at node 2 and 3.

Q: 1-Two rivets holds three sheets of steel together, and is loaded as shown below. If the maximum…

Question

Q.3. The right-angle bar shown in figure (3) is supported by a pin at B and a roller at C. What is the
maximum value of the load P that can be applied if the ultimate shear strength of the pin is 30000 psí? The
3/4 inch diameter pin is in double shear. Use factor of safety = 1.5.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

ASAP
Problem 1.3-5. The truss shown carries two forces: a horizontal rightward force of 50 kN and a vertical downward force of 100 kN. A roller supports the truss at A and a pin at H. If the pin's allowable shearing stress is 150 MPa, solve the pin's minimum diameter to carry the applied load safely. (Hence: The pin at A is at a state of a double shear.) D. B. 50 kN 1 m 1 m H. 1 m G. 1 m 1 m Detail at A 100 kN
please answer quickly
For a given Data of the riveted joint shown in the figure: Given: Diameter of each rivet = 3/4 inch Maximum allowable shear stress of rivet = 96.53 MPa 3. Maximum allowable bearing stress of plate = 124.11 MPa %3D Yield Strength of the key = 45 MPa Ultimate Strength of the key = 128.5 MPa %3D Determine the maximum safe value of P that can be applied to both ends in Kips or Kilo pound. The figure below: 4 in P 7/8 in 7/8 in
Figure 2 shows a horizontal beam AB. It is pin-supported at end A and carrying a load Q at end B. The beam is supported at C by a pinned-end column. The column is a solid steel bar of square cross-section having length L and side dimension b = 60 mm. Based upon the critical load of the column, if the allowable load Q is given by 109 KN with the factor of safety n = 2.0 with respect to buckling, determine the length of the column. E = 200 GPa 2d Q Figure 2 (201
Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure below. The joint material has the following allowable stresses: tensile stress = compressive stress -50 Mpa, shear stress =35 Mpa and crushing stress = 90 Mpa. (Assuming: the load is applied statically). P- C1 78 mm C1 78 mm C2 C3 C3 156 mm 98 mm C4 C1 C5 C1 60 mm C4 C5 P. C5 C2
What is the shear stress developed on the UPPER spring (in MPa)? What is the shear stress developed on the LOWER spring (in MPa)? What will the total elongation of the spring (in mm)? indicate the free body diagram
Please help. This problem involves torsional stress and strain. Thank you.
Uniform AB brass rod has a rectangular vertical cross section, fixed with support and pin as shown in the figure. Both ends of the rod are free in the vertical direction but rotation in the horizontal direction is prevented. a) Find the b / d ratios at the safe boundaries for the horizontal and vertical axes?b) What would be the safety factor if P = 1.8 kN, L = 7m, d = 60mm and E = 150GPa?
question is on the figure
The hollow cylinder shaft shown in the figure has an inside diameter of 15mm and the gears are subjected to the indicated load. The bearings at points A and B only exert forces on the shaft in the y and z directions. If the allowable shear stress is known to be operm = 70 MPa. Use the maximum shear stress theory of failure and proceed to:a) Draw the bending moment diagrams My and Mz and torque T, determine the magnitude and location of the absolute Maximum Moment.b) Determine the outer diameter of the shaft to within 1 mm.