Q.3) A structural member in plane strain has the following strains at a point: Ex = 360 µ, 8-230 μ , Χ- 150 μ (a) Determine the strains for an element oriented at an angle of 60° counter clockwise. (b) Determine the principal strains and the maximum shear strain using strain transformation equations. (c) Show the result of parts (a) and (b) via sketches of properly oriented elements. Ey Yxy Ex

Q.3) A structural member in plane strain has the following strains at a point: Ex = 360 µ, 8-230 μ , Χ- 150 μ (a) Determine the strains for an element oriented at an angle of 60° counter clockwise. (b) Determine the principal strains and the maximum shear strain using strain transformation equations. (c) Show the result of parts (a) and (b) via sketches of properly oriented elements. Ey Yxy Ex

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As a result of the tension applied from the base in the X axis, the strain value of the structure in the same direction was measured as 0.26 mm / mm. Under the same loading condition: a) Calculate the strain of the structure in the Z axis. b) In this case, what is the type of strain on the Z axis?
4.7. Show that the direct strain-component in the y-direction is given by (Fig. 4.6). Figure 4.7 (Evv)s an ay Ay A x Ax Ay D' any Ay Figure 4.6 1 Ax
2.5
A differential element on the bracket is subjected to plane strain that has the following components: , Ex = 300 x 10-6, Ey = 200 x 10-6, Exy = -500 x 10-6. Use the strain-transformation equations and determine the normal strain Ex' in the x' direction on an element oriented at an angle of 60°. Note, a positive angle is counter clockwise.
can you answer full detail ,ı need to understand fully ,thanks in advance
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 9 mm & Modulus of Elasticity 205 GPa. It is found that the specimen has undergone an extension of 1.7 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain-induced due to the load "F" on the specimen is 3.7 x 10-3. Solution Cross-sectional Area, A (in mm2) Tensile Load, F (in N) Length of the Specimen (in mm)
mehcanics of deformable bodiesplease answer asapno.6
A rigid steel bar ABC is supported by threerods made of steel [E=200 GPa]. There is no strain in the rods before load P is applied. After load P is applied, the axial strain in rod (1) is 1,200 µɛ. اسوزن Jago 1,500 mm (a) Determine the axial strain in rod (2). (b) The normal stress in rods (1) and (2). 900 mm (1) (2) (2)
Consider the following strain state: [0.0016 0.0003 [0] = 0.0003 0.0008 0 0 0 0 0.0004] a. Determine the strain matrix for this strain state if the axes are rotated 30° counterclockwise around z-axis. b. Plot Mohr's circle for this strain state.
Your answer is partially correct. The strain components for a point in a body subjected to plane strain are ɛ, = -890 µɛ, ɛ, = -690µɛ and yy = -682 prad. Using Mohr's circle, determine the principal strains (ɛp1 > Ep2), the maximum inplane shear strain yip, and the absolute maximum shear strain ymax at the point. Show the angle 0, (counterclockwise is positive, clockwise is negative), the principal strain deformations, and the maximum in-plane shear strain distortion in a sketch. Answers: Ep1 = 927.99 με. Ep2 = 1116.0 PE. Vip = 188.01 prad. Ymax = -188.01 prad. Op = 36.82