Q.2 Determine the vertical displacement of joint C of the steel truss shown. The cross-section area of each member is A = 400 mm2 and E = 200 GPa (x) = 4 412= 0=4 =402 D 2 E 4 B 4 m 4 m 4m 4 KN 4 KN 4 m

Q.2 Determine the vertical displacement of joint C of the steel truss shown. The cross-section area of each member is A = 400 mm2 and E = 200 GPa (x) = 4 412= 0=4 =402 D 2 E 4 B 4 m 4 m 4m 4 KN 4 KN 4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A wide flange is used as a beam that is simply supported at its ends.The properties are shown.A = 19600 mm². by = 229 mmL = 1249 x10^4mm te=14 mm Tx = 25.4 mm tr = 24.9 mm ly = 49.5 x10^4mm d = 623 mm Ty = 50.5 mm If the beam is laterally supported at supports only, determine the allowable bending stress for a length of; 1. 2m 2. 4m 3. 6m 4. 8m
From the figure shown, a truss is subjected to loads PI = 15 kN, P2 = 15 kN and P3 = 25 kN at joint C, D and E respectively. Use SI = 3 m; S2 = 4 m P₁ Properties of diagonal members (2L75 x 75 x 6): Ag = 1858 mm2 Fy = 248 MPa rx = 22.9 mm ry = 33.2 mm G a) What is the axial force in kN, in member DI? b) What is the allowable stress in MPa, in member DI? c) Calculate the allowable load in kN, in member DI. H 6 @ Si I P₁ E B S, CIVIL ENGINEERING- STEEL DESIGN ...
All members of the truss have the same length L=4.4 m. Determine the MAGNITUDE (N) of force supported by member CE if P=828 N. Round off only on the final answer expressed in 3 decimal places.
From the figure shown, a truss is subjected to loads PI = 15 KN, P2=15 kN and P3-25 kN at joint C. D and E respectively. Use 5l = 3 m; S2 = 4 m P₁ Properties of diagonal members (2L75 x 75 x 6): Ag = 1858 mm2 Fy=248 MPa rx = 22.9 mm ry = 33.2 mm a) What is the axial force in kN, in member DI? b) What is the allowable stress in MPa, in member DI? c) Calculate the allowable load in kN, in member DI. H 6 @ S₁ CIVIL ENGINEERING- STEEL DESIGN ***
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. A 7.8 m 36° Answers: AB= AD = BC= BD = CD= i Fat D 6.9 m i 6.9 m 7.8 m B 6150 N N N N N C N
The steel framework is used to support the reinforced stone concrete slab that is used for an office. The slab is 200 mm thick. Sketch the loading that acts along members BE and FED. Take a = 3 m, b = 4 m. Hint: See Tables 1.2 and 1.4.
Determine the forces in members BF,BC,EF in the truss shown. Solve using Method of sections. Quickest solution. Only solve for what is asked for.
Calculate all the member forces in the given truss using method of consistent deformation. Joint D is pinned supported and joint E is roller supported. F=4450 kN and L=8m. Take 'EA' same for all members В F 1 2 L 3 5 4 E
Analyze the Structure given in Figure (Picture Attached) and determine the forces in each member of truss by Methods of Sections. State whether members are in tension or compression. P1= 720KN P2= 360KN
Problem 2 Compute the axial stresses in the beam AD and in the truss BC. Consider the contribution of the axial load to the bending moment. L = 100 in, αABC= 30 deg,AB = 70 in, E = 10000 ksi,IAD = 10 in*, ABC = 5 in². All the cross-sections are square. W = 10 lb./in. A Pin Pin 5 B Pin Fig. A2.1 D
Determine the joint displacements, member end forces, and support reactions for the beam shown. 15 k 15 k 5 k/ft 4 3 - 25 ft -- 25 A - sA +-8a -8A -| El = constant E = 10,000 ksi I = 540 in.+
DETERMINE THE BAR FORCES OF THE GIVEN TRUSS IN TERMS OF VARIABLE "P" APPLYING ANY METHOD OF ANALYSIS. STATE THE NATURE OF FORCES. IF THE VALUE OF P= 15KN, WHAT IS THE MAXIMUM TENSILE BAR FORCE VALUE OF CD,BC,AB,AE,BF,DF,CE,DE