Q.2- Answer with true and false, and correct false statements.1- Loading time of concrete starts from the first contact between water and aggregate.2- Time of formwork striking increases with increasing of ambient temperature but it decreases withincreasing of active space of concrete slab.3- Concrete quantity measured by weight of hardened concrete.4- Minimum concrete cover thickness depends on diameter of reinforcement bars only.5-Columns capital and drop panels must be placed with columns monolithically.

Part 1 Loading of concrete starts from placing of concrete rather than mixing. Hence False Part 2…

Q.2- Answer with true and false, and correct false statements. 1- Loading time of concrete starts from the first contact between water and aggregate. 2- Time of formwork striking increases with increasing of ambient temperature but it decreases wit increasing of active space of concrete slab. 3- Concrete quantity measured by weight of hardened concrete.

Q.2- Answer with true and false, and correct false statements. 1- Loading time of concrete starts from the first contact between water and aggregate. 2- Time of formwork striking increases with increasing of ambient temperature but it decreases wit increasing of active space of concrete slab. 3- Concrete quantity measured by weight of hardened concrete.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The concrete weigh 8.5 kg. Find the specific weight of the concrete using the dimensions shown in the picture.
Internal diameter and depth of cylindrical steel cup are mm and mm in Aggregate Impact Value test. А. 204 mm, 100 mm В. 61mm, 25 mm C. 150 mm, 75 mm D. 102 mm, 50 mm B.
Using the Table Below, what is the approximate value of the match line if k=100, Ec=6x10^6, J=4, and the rest is the same with the example. Concrete elastic modulus, E. (106 Ib/in²) 10 20 1200 1100 4.5 4.0 30 1000 40 900 3.0 800 50 2.2 700 60 600- 70 500 80 - 800 400 200 100 50 Effective modulus of subgrade reaction, k (Ib/in3) 20 10 90 100 Example: k = 72 Ib/in3 E = 5 x 106 Ib/in? R = 95% (ZR = -1.645) S = 650 Ib/in? J= 3.2 S, = 0.29 APSI = 4.2 - 2.5 = 1.7 W18 = 5.1 x 106 (18-kip ESAL) Solution: D = 10.0 inches (nearest half-inch, from segment 2) C4 = 1.0 10 sninpow ajajɔuon GuIvai) 's 'əunadna Load transfer coefficient, J ~ Drainage coefficient, Cí Match line
What is the w/cm for the following 1 m3 batch of concrete? Express your answer with 2 decimal places. Material Batch mass, kg Cement 250 Pozzolan 84 Fine aggregate (absorption 0.8%. moisture content, 4%) Coarse aggregate (absorption 0.4%. moisture content 1.5%) Water added to the batch mix 623 1177 116
pls answer soon
MAKING AND CURING OF CONCRETE TEST SPECIMENS what is the volume of concrete?
Do not give answer in image and hand writing
Subject reinforced concrete design solve p02
In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect any mix problem and to ensure that the compressive strength is higher than the lower specification limit. The minimum target value was set at 27.6 MPa. The compressive strength data shown in Table P7.48 were collected. Use one system of units only as specified by the instructor. a. Calculate the mean, standard deviation, and the coefficient of variation of the data.b. Using a spreadsheet program, create a control chart for these data showing the target value and the lower specification limit. Is the plant production meeting the specification requirement? If not, comment on possible reasons. Comment on the data scatter.
20 The figure below shows relative frequency histogram for 50 concrete cubes classified according to compressive strength of the cubes. While x- axis represents the class midpoints of compressive strength, y-axis represents relative frequency for concrete cubes. Determine the harmonic mean of compressive strength * .of the cubes Relative Frequency Chart 0.45 0.4 0.35 0.3 0.25 능 0.2 7 0.15 0.1 0.05 25.5 35.5 45.5 55.5 Class Midpoints of Compressive Strength Relative Frequency for Concrete Cubes
*I E,90 KB/S H.W (4)-2nd cours... Concrete technology H.W (4) (A) Give reasons: Very early strength of concrete increases if temperature during placing and setting is increased. This is not the case for concrete strength after 7 days. (B) / Explain the following curve (use your own words (DO NOT COPY FROM THE LECTURE & DO NOT COPY FROM OTHER RESOURCES). 10000 Age at Test ePonded 8000 Hessian days 6000 bnded Hessian 4000 Ponded days Hessian Ty 2000 032 040 Woter / Cement Ratio 036 044