Q.1 A simply supported beam of span 2 mcarries a uniformly distributed load of140KN/m over the whole span. The crosssection of the beam is a T section with flangewidth of 120 mm, web and flange thickness of20 mm and overall depth of 160 mm.Determine the maximum shear stress in thebeam and draw the shear stress distributionfor the section. (2.5 M) 120- 53.08 90 160 140Y (mm) 20 Answer:

givenlength of span L=2muniformly distributed load intensity W=140kN/mcross section of beam is T…

Q.1 A simply supported beam of span 2 m carries a uniformly distributed load of 140KN/m over the whole span. The cross section of the beam is a T section with flange width of 120 mm, web and flange thicknes of 20 mm and overall depth of 160 mm. Determine the maximum shear stress in the beam and draw the shear stress distribution for the section. (2.5 M) 120- 53.0890 160 140

Q.1 A simply supported beam of span 2 m carries a uniformly distributed load of 140KN/m over the whole span. The cross section of the beam is a T section with flange width of 120 mm, web and flange thicknes of 20 mm and overall depth of 160 mm. Determine the maximum shear stress in the beam and draw the shear stress distribution for the section. (2.5 M) 120- 53.0890 160 140

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

0.4m The beam is subjected to a shear of y=30 kN. Determine the maximum shear stress in the beam. O.L4 m 0.1m 0.1m て=VQ O.4m It 0.4m Section # * Cm) A Cmiy 0.4m 0.1m R=0.0 36 m 0.4m 0.55 m 0.04 (0.55-
Draw the shear force diagram of the following beam..
If the force P = 33 KN and the distributed load w = 6 KN/m. then, the slope at point A is knowing that EI = 13 x 106 W A -2 m- 2 m a. 0.00131 b. 0.03524 c. 0.00055 d. 0.02092
The beam is subjected to a moment M-17.6 kN-m. Determine the maximum bending stress given a=60 mm and b=160 mm. a a 20 mm 20 mm 20 mm 20 mm 20 mm D- 20 mm O 12.097 MPa O 8.512 kPa O10.215 MPa O12.097 kPa O7.567 kPa O 10.215 kPa 7.567 MPa 0 8.512 MPa
The possible location of shear centre of the channel section, shown below, is F iR S P Q
A built-up beam made from fastening two channels to a wide flange section carries loads as shown. The fasteners are 12mmØ bolts with allowable shear stress t = 110 MPa. For bearing op = 220 MPa for single shear, and op= 275 MPa for double shear. E= 200 GPa. Fy= 420 MPa a. Determine the spacing of the bolts.
I’m confused if I’m doing this right and where to go next
please help
The beam is subjected to a uniformly distributed load. What is the maximummagnitude of the average shear stress in the beam, and where does it occur?
The bending moment acting on the triangular cross section of a beam is 3.6 kN m. Determine the maximum compressive stress in MPa acting on the cross section. 60.00 120.00
Q5/ If the beam has a square cross section of 9 in. on each side, determine the absolute maximum bending stress in the beam. 1200 Ib 800 lb/ft |A -8 ft- -8 ft-
ينب