Q. Dexive expressive for hammer blow as applied to Lo comobive Balancing,

Q: ④ Comparision between forced and Induced draught.

A: (1) Fan is installed near or at the base of the boiler(2) It handles low temperature and less volume…

Q: If the length of the side of a body-centered cubic structure is 300 pm, what is the radius of the…

A:

Q: tarting friction is low in: A.   Hydrostatic lubrication B.   Hydrodynamic lubrication C.   Mixed…

A:

Q: Hollow and solid shafts have the same material, length and the same outer radius as shown. The inner…

A:

Q: m The figure shows an inverted pendulum. Identify the equation of motion in terms of the angle o.…

A: Deriving the equation of motion.

Q: Replace the loading by an equivalent resultant force and couple moment acting at point Suppose that…

A: Given data: w=65 lb/ft Need to determine the resultant force and couple moment about the point O.

Q: Mercury will always have a hairline lift. Select one: O True O False

A: False: Grammatical mistake ('has' is place of 'have') Also, in mechanical engineering context ,…

Q: A double-acting cylinder is to be used to emboss plastic rulers. The cylinder may only extend when…

A: as the press tool is the device in which the sheet metal components are are produced in large volume…

Q: The figure below gives the moment of inertia Io for a point mass rotating about point O. As a…

A:

Q: What impact does a rigorous lubrication program have on a facility?

A: The path to lubrication excellence is tough to navigate. It begins once people and organizations…

Q: 6. The steel shaft shown rotates at 3 rev/sec with 30 kW removed at A, 15 kW taken off at B, and 45…

A:

Q: An example of a performance with two phases is the bench press; in the down phase the lifter lowers…

A: The preparation phase and the movement phase of the bench press exercise can be separated.…

Q: Part A A steel tube having an outer diameter transmit 9 hp when turning at 27 rev/min. 1 hp = 550…

A: Given data:The outer diameter, do = 2.5 in.The power transmitted, P = 9 hp.The turning revolution, N…

Q: What down the external sources of induced foot?

A: The external sources of induced foot are:-

Q: What is statically balance forces

A:

Q: As shown in the figure. A plot of potential energy U versus position x of a 2 kg particle that can…

A: Calculate the total energy of the particle when it is released at the position x=5 m i.e. at point…

Q: Acidizing removes damage near wellbore by injecting fluid into the formation above the fracturing…

A: Option b is correct  True

Q: А В C

A:

Q: Assume the disk is rolling on a slippery surface (it rolls and slides). How many degrees of freedom…

A: Explaining the degree of freedom of system.

Q: A 02-series deep - groove ball bearing is to be selected to carry a radial load of 8 kN and a thrust…

A: Given-02-series deep ball bearingRadial load=8KNThrust Load=4KNLife L=5000hpl=900rpmReliablity=0.90

Q: 1) The working face of ordinary flat key is 1 A. Side B. Upper top surface C. Bottom surface D. End…

A: (1)

Q: Identify the equation of motion for the system shown in this figure. Discount the mass of the L-…

A: Deriving the equation of motion.

Q: 2. The hinged component shown in Fig. 2 is used to activate a latching device for securing a large…

A:

Q: Elaborate which balancing method is performed for wheel/tire balancing process over there and give…

A: wheel or Tyre balancing :-

Q: appliication of flash, fire, and pour points of lubricants and fuels

A: Flash point: It is the lowest temperature at which the given liquid provides sufficient vapor to…

Q: Which of the following is the first sign of a need for lubrication? A. Unusual vibration B. Unusual…

A: Lubrication plays a crucial role in reducing friction between moving parts. It forms a thin film or…

Q: explain the apparatus and its working which is used for wheel/tire balancing.

A: Wheel or Tyre balancing :-  In many cases, when a tire is manufactured, it is inspected for static…

Q: A 100N load is added to the end of circular cross section steel rod that has a length of 0.3m and a…

A: GIVEN DATA- Length of bar L=0.3m Diameter of bar d=0.025m Load P=100N Young Modulus…

Q: Hydraulic drive is considered heavy duty and provide a smooth and strong movement within the machine…

A: From the analysis of the above figure

Q: To maintain the optimum performance of a computer chip, its surface temperature should not exceed…

A:

Q: 6. The steel shaft shown rotates at 3 rev/sec with 30 kW removed at A, 15 kW taken off at B, and 45…

A:

Q: (External flow character) A023-m-diameter soccer ball moves through the air with a speed of 10 m/s.…

A: Diameter,D=0.23 mVelocity,V=10 m/sTo determine:a)Reynolds number(Re)b)Classification of flow

Q: Describe tapper noise

A: Ther is a concept called tappet noise When the engine is running ideally there comes a regular…

Q: An ideal gas is taken through a quasi-static process described by P = aV2, with a = 4.80 atm/m, as…

A:

Q: AT OVERHANG( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).

A:

Q: Describe with characteristics details for sink washer.

A: In plumbing, a sink washer is a kind of perforated metal strainer or cross section sifter used to…

Q: va three DoF (Degree of freedom) eight link (n=8) mechanism with rev rify DoF mechanism using…

A:

Q: A 40-kg packing crate is pulled by a rope as shown with a force P = 200 N. The coefficient of…

A: