Q. An AM/DSB-LC signal has a power of (S) watt, the maximum frequency of the baseband signal is (fmax) Hz, while the carrier frequency is (fc) Hz. If the additive noise power spectral density (two-sided) in the transmission channel is: Sn(w)=A/w^2 Given A=208 Fc=53244 Fmax=5754 S=26 * ?What is the upper sideband frequency value (1 - ?What is the lower sideband frequency value (2 ?What is the noise p ower value (3 * ?What is the SNR value (4

Q. An AM/DSB-LC signal has a power of (S) watt, the maximum frequency of the baseband signal is (fmax) Hz, while the carrier frequency is (fc) Hz. If the additive noise power spectral density (two-sided) in the transmission channel is: Sn(w)=A/w^2 Given A=208 Fc=53244 Fmax=5754 S=26 * ?What is the upper sideband frequency value (1 - ?What is the lower sideband frequency value (2 ?What is the noise p ower value (3 * ?What is the SNR value (4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please provide Handwritten answer
Qi. An Am mo dulation waveform Signal = lo (1+0.5 cos Z000TE + o.5 cos yo007Tt).cos 20000t Q plot the amplitude spectrum of Øe4) . O Find the modulation Index . © find total power, Sideband power & power efficiency.
For single-sideband production in AM SSBSC, three transmitter configurations are typically used: the filter approach, the phase-shift method, and the so-called third method. A bandpass filter circuit is used in the filter method to reject one sideband and transmit the remaining sideband. The modulating signal and carrier are applied directly to one of the modulators in the phase-shift method, then both are moved 90 degrees and applied to the second modulator. The outputs of the two balanced modulators are double-sideband suppressed-carrier signals with the proper phase, so that one of the sidebands is canceled when they are combined in a linear summer. The disadvantage of single-sideband transmission is which of the following statements? Select your answer. Tuning single-sideband receivers is more difficult and precise than tuning DSBSC AM receivers. Because most single-sideband transmissions involve a suppressed carrier, envelope detection cannot be employed unless the carrier is…
In an AM modulation, modulating signal is m(t) = 2 cos wmt and modulation index is given as u = 0.72 a) Sketch the AM signal. b) Şketch the frequency spectrum of the AM şignal. c) Find the bandwidth of the AM signal. d) Calculate the power of AM signal, carrier signal and sidebands
The SNRi of an FM transmitter is determined to be 24.093dBV. Solve for the peak frequency deviation caused by the noise if the transmitter sensitivity is determined to be 368.903Hz/V, and a modulating signal of 13.926V and the modulating index is kept at 4
14.a. While conducting an OTDR trace, you find that the signal strength drops by 0.091 dB over an 82 m section of fiber. What's the attenuation in this fiber?A. 0.80 dB/kmB. 7.46 dB/kmC. 0.91 dB/kmD. 1.11 dB/km14.b. Which component converts an optical signal into an electrical signal in a transceiver?A. LEDB. EDFAC. Optical modemD. Photodiode
digital communicationA signal was represented using Bipolar RZ with a bandwidth of 40 kHz, then thebandwidth will be …………. If Bipolar NRZ was used.
-The modulating signal 2cos (2 π×103 t) is used to modulate a carrier signal 40cos (2 π×104t). Evaluate the modulation index, percentage modulation, frequency of side band components and their amplitudes .What is the bandwidth of a modulating signal.
[Q1] A carrier signal (peak amplitude = 39V, frequency = 100MHZ) is frequency modulated by the baseband signal (peak amplitude = 5V, bandwidth = 12.02kHz). The frequency deviation is 77.53kHz, and the load is 51N. Determine (a) the load power, (b) the bandwidth of the transmitted signal. (consider only Jn(B)| > 0.1). %3D
H.W A) An amplitude modulated signal has a carrier frequency 10KHZ. The upper sideband is transmitted at 11KHZ. plot the frequency spectrum and determine the Bandwidth required for the AM signal? B) compute the Signal Energy
ii) A single sideband AM signal (SSB-SC) is given by s(t) = 10cos(11000 πt). The carrier signal is c(t) = 4cos(10000πt). Determine the modulating signal m(t).
Question 3 (a) Briefly explain THREE (3) disadvantages of Single Sideband (SSB) over Double Sideband Suppressed Carrier (DSBSC). (b) An AM DSBSC signal with a load resistance 50 2 has the following equation: VaMt) = 8 sin 21.53 x 10°t sin 11.88 x 10°t (V) i. Calculate the upper and lower sideband frequencies. ii. Determine the bandwidth. iii. Calculate the total power. iv. Sketch and label the resultant frequency spectrum. (c) An AM DSBFC signal has a carrier frequency of 300 kHz with peak amplitude is 17 V. The modulating frequency is 15 kHz with peak amplitude of 6 V. i. Determine the peak amplitude of the modulated sidebands. ii. Calculate the maximum and minimum amplitude of the envelope. iii. Sketch and label the resultant frequency spectrum. iv. Sketch and label the modulated signal in time domain.