36Asiacell9:rV IO Z.ovKOREKO resonance qui...->University of BaghdadCollege of EngineeringElectronics & Communication Dept.Electrical Circuits IISecond Stage2020-2021Duration: 40 minutesQ. A series RLC circuit has a quality factor of 5.1 at a resonance frequency of100KHZ. Assuming that one-half of the maximum dissipated power is 100Wand the maximum current is 0.8A. Calculate the circuit element values andthe B.W.

Solution:- Given: Po2=Io2R2=Io22 R ⇒Po2=0.707 Io2 R=100w→…

Q. A series RLC circuit has a quality factor of 5.1 at a resonance frequency of 100KHZ. Assuming that one-half of the maximum dissipated power is 100w and the maximum current is 0.8A. Calculate the circuit element values and the B.W.

Q. A series RLC circuit has a quality factor of 5.1 at a resonance frequency of 100KHZ. Assuming that one-half of the maximum dissipated power is 100w and the maximum current is 0.8A. Calculate the circuit element values and the B.W.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine the impedance magnitudé at frequencies:0 %. 1KH2 be low fo 3ikHz above fo. (Ans: 1or, l.42 Kse, 1.15 kr) Vs =50L0 V
For circuit shown in the figure with Voc=9 V, Rg=354 kn, Rc=409 0, RE=2.6 kn, B=117, VeE=0.7 V, determine S(lo). Vcc Rc RB Vc |VCE oVE emitter bias configuration Lütfen birini seçin: a.63.38 b.71.86 c.61.96 d.37.75 e.56.97
Q.9: For the circuit shown: 1. Find the value of "Rc" that makes the circuit in resonance. RL RC VT 1020°v 2. Calculate the total current at resonance. 3. Find the minimum & maximum power dissipated by the circuit. (Ans.: Rc=7.642, to=1.72A, Pmin=8W, & Pmax=18W) YT. XL Xc J60
4.) Given the following LRC circuit (L = .012 H, R = 8 ohm, C = 2 F, w = 2*60*pi), Vmax = 100V. A.) Draw a phasor diagram of the circuit. B.) By what degree does the voltage source lead or lag the current? C.) What frequency of the voltage source is necessary to reach resonance?
(7 (6) Find the low frequency response by determining poles due to each coupling and hypass capacitor (CE, Cin & Cont). Ignore to for the BJT. 2/5 + Ps M Cin Vcr R₂ Vcc T R₂ Cont " ERL Vout
For given BJT, B=200. The applied input frequency is 20 Mhz and net internal capacitance is 100 pF. What is the CE short circuit current gain at ẞ cut-off frequency?
If vsig is a triangle waveform, determine the maximum amplitude that vsig can have? Showyour calculation.
Q. A series RLC circuit has a quality factor of 5.1 at a resonance frequency of 100KHZ. Assuming that one-half of the maximum dissipated power is 100W and the maximum current is 0.8A. Calculate the circuit element values and the B.W.
An amplifier has a spectrally pure sine-wave input of 50 mV. It has a voltage gain of 60. A spectrum analyzer shows harmonics of 0.035 V, 0.027 V, 0.019 V, 0.011 V, and 0.005 V. Calculate the total harmonic distortion (THD) and the relative harmonic distortion.
Q1) for the BJT circuit shown with (B = 120) determine low cutoff frequencies and what is the effective low cutoff frequency 18 V 2 kN 30 k2 3 µF 15 µF 10ka 1.46 k2 6 µF
For given BJT, B=200. The applied input frequency is 20 Mhz and net internal capacitance is 100 pF. What is the CE short circuit current gain at ẞ cut-off frequency?