Q/ What does this mean in an electrical single line diagram? L1 11kV 50HZ 3PH 3 WIRE 2000A 40KA FOR 1 SEC. 100kA PEAK L2 L3 MECHANICAL TRIP FACILITY 52 VCB PV100 1250A A i2kV 40KA MECHANICAL IN TERLOCK (NOTE 4) EARTH SWITCH SURGE ARRESTERS

Q/ What does this mean in an electrical single line diagram? L1 11kV 50HZ 3PH 3 WIRE 2000A 40KA FOR 1 SEC. 100kA PEAK L2 L3 MECHANICAL TRIP FACILITY 52 VCB PV100 1250A A i2kV 40KA MECHANICAL IN TERLOCK (NOTE 4) EARTH SWITCH SURGE ARRESTERS

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For a system if the value of peak overshoot is 16 %, then the value of damping ratio o is
A 107 hp, 257 V de shunt motor has the magnetization curve in the graph. The armature circuit resistance, including brushes, is .032 ohm. no load rotational losses are 2087 w and the stray loss is 1% of the output The field rheostat is adjusted for a no-load speed of 1107 pm a. What would be the field current at no load when speed is 1100 rpm b. Determine Speed and output in horsepower corresponding to an armature current of 400A c. Now a cumulative series turns 2 (N) per pole is to be added with R negligible and 1000 turns in Shunt field find speed corresponding to an armature current of 400A
Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…
draw in all the current flow paths of lines x and y are at +5 volts and z is at 0 volts SOLID STATE EQUIVALENT 10-1 YOK N zo K 4S V 0 Qi Ry -011 OFF Q₂
If the per unit reactance of a power system up to the fault point is 0.1pu and base power (VA) is 10 MVA, then the fault level (VASC) is ut of O 100 MVA 2 MVA O 50 MVA O 500 MVA МacВook Air DII DD F11 F10 こ: F9 000 F7 F8 F6 F4 F5 * & 7 V 8 A9 a 5 0 6.
For the circult shown In Figure A10, The value of current is calculated as R MO- 2.5V 3.65 kn 5.5 VO Figure A10 O a. 2 mA O b. 2.10 mA O c. 0.74 mA O d. 0.63 mA English (United States) o search 近
Refer to figure 2. Calculate fault current
4. The maximum current passing through device is 125 mA. Find the instantaneous current when e=225^0 a. -125 mA b. -176.7767 mA C. -62.5 mA d. -88.3883 mA
If load sets are in parallel and inside each load set the lamps glow a. Few bright b. Dim C. none of them d. Bright
I need to solve the question in 10 minutes, please
PLEASE ANSWER THIS QUESTION (Q1B)
Q2: Equipment ratings for the four power system shown in Figure (1) are as follow: - GI-500 MVA, 13.8 kV, X = 0.2 p.u G2-750 MVA, 18 kV, X-0.18 p.u G3-1000 MVA, 20 kV, X-0.17 p.u TI = 500 MVA, 13.8/500 kV, XT1=0.12 p.u T2-750 MVA, 18/500 kV, XT2= 0.1 p.u T3-1000 MVA, 20/500 kV, XT3-0.1 p.u. (1) T1 T3 T.L 1 G1 j50 ohm 13,8/500 KV 20/500 kV T.L 2 j50 ohm T.L 3 150 ohm T2 G3 18/500 KV G2 Figure (1) neglecting resistance, transformer phase shift, and magnetizing reactance, draw the positive - sequence reactance diagram on a 1000 MVA, 20kV base in the G3.