Q/ In the equilibrium positionshown in figure below, theuniform bar (AB) has a massof (50 kg) and supports load(200 kg) at (A). Determine thetension (T) in the cable andreaction force at (B)?2.5m2.5mBi:1200 kgT = 6511 N, FBx = 3823 N, and FBy= 8992 NT = 7646 N, FBx = 3823 N, and FBy= 4169 NO Non of the aboveT = 7646 N, FBx= 2000 N, and FBy =3299 N

Answered: Q/ In the shown in figure below, the…

Q/ In the shown in figure below, the uniform bar (AB) has a mass of (50 kg) and supports load (200 kg) at (A). Determine the equilibrium position 17 ·

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A bar AB of weight 180kN is hinged at A and held at equilibrium by a force P as shown in the figure. Determine the magnitude of force P about the hinge reaction at A for the equilibrium position of the bar AB. Take the length of the bar as 10m.
The lid shown has a mass, m = 60 kg, and is held in position by rod AB. The rod is held in place by rounded surfaces at A and B, where B is right at the edge of the lid. The hinges at C and D rotate smoothly and only the hinge at C provides a reaction force along its axis (the x-direction). a = 950 mm, b = 300 mm, c = 55 degrees Determine A) Reactions at hinge C and D B) Reaction force in rod AB C) The minimum coefficient of friction that is needed between the rod and the lid to maintain this position
Consider the frame shown in (Figure 1). The suspended cylinder has a mass of 45 kg. Determine the x and y components of reaction at pin B on BC using scalar notation. Determine the x and y components of force at pin C using scalar notation.
Problem 3 The boom AB supports a load of W = 720 lb. The boom is supported by a ball-and-socket joint at A and by two cables, BC and BD. Find the tension in each cable and the axial force in the boom, assuming that point C is 4 inches vertically above the position shown in the figure and the other dimensions are unchanged. Neglect the weight of the boom. -9 in.- 8 in. B 12 in. W = 720 lb %3D
Q/1: A 10 m long vertical mast has a ball-and socket joint at A, and it is supported by two (2) cables, BD and BC as shown in Figure 1. A force 4 kN is applied at G. Draw the free body diagram (FBD) for the rigid body and determine: (a) The tensions in cables BD and BC (b) The reactions at the ball-and-socket joint at A (c) The projection of T, along the line BE (d) The angle between cable BD and line BE (e) The moment of T, along line CF T2 4 kN 5 m B 5 m T₁ 4m-F 74 m 12m x
The bar ABCD of negligible weight has a built in support at point A. It is subject to loads as shown in the figure. a) draw the FBD of the bar. b) write the external loads in their vector forms. c) write the 3D static equilibrium equations for the bar and solve for the reactions.
A sign of mass 6.2 kg is hanging from a uniform beam of mass 11.2 kg and length I as shown in the diagram below. Here e 51.3 and 51A. The beam is in cquilibrium. Calculate the vertical force at the hinge. 90 -e
Determine the reactions at point A and B of the parallel force system shown in the figure to the right. Neglect the weight of the supporting member. 5940 lb 1170 lb/ft B 3.00- 5.00 -6.00 4.00- LENGTH IN FEET Question 2 v Saved Listen Location from the left end of the beam to the concentrated load that will replace the uniformly distributed load:
A homogeneous rectangular flat plate that weighs WN is supported by a shaft AB and a cable C as shown in the figure. The bearing at A is a thrust bearing, and B is a radial (ball) bearing. For the loading condition shown in the figure, determine the reactions at bearings A and B. (Draw Free-Body Diagram of the system. Use a VECTORAL ANALYSIS for the solution).
The figure shows a uniform beam of mass m pivoted at its lower end, with a horizontal spring attached between its top end and a vertical wall. The beam makes an angle e with the horizontal. (a) Find an expression for the distance d the spring is stretched from equilibrium. (Use any variable or symbol stated above along with the following as necessary: k and g.) d = (b) Find expressions for the components of the force exerted by the pivot on the beam. (Use the following as necessary: m, k, g, and 0. Assume the positive x-direction is to the right and the positive y direction is upward.) Ry- Ry=
9. The boom AC in the figure rests in a ball and socket joint at A and is held in equilibrium by the cables BE and CD. The load applied at C. Determine the coordinates of D in the YZ plane so that the force in CD will be a minimum. Neglect the weight of the boom and cables. Answers: y = 16 ft; z = -34.7 ft 4'1 300 Ib 900 Ib Note: The reaction at ball and socket joint is always represented by thè x, y and z components. ETER
The compound beam shown in (Eigure 1) is fixed at E and supported by a rocker at A and B. There are hinges (pins) at C and D. The 4-kN load is applied just to the right of the pin at D. Suppose that w = 5 kN/m. Figure 4 kN 6kN I. conf 1 of 1 -2m-2m-2m-3m- 3m ▼ Determine the y component of reaction at A. Express your answer to three significant figures and include the appropriate units. A₁ = Value Submit Part B B, = HA Submit Part C Request Answer Determine the y component of reaction at B. Express your answer to three significant figures and include the appropriate units. Value KN Request Answer ? KN ? Determine the component of reaction at E.. Express your answer to three significant figures and include the appropriate units.