Q: Find the height of the building using the information collected via a theodolite provided in the below illustration. Show calculation process B Top hair reading Bottom hair reading Top reading 1.73 Bottom reading 1.61 119° 20' 11" 125° 16' 13" 1.73 1.61 Drawing not to scale 119° 20′ 11″ 125° 16' 13" B

Q: 440 (kN) .09 2m 220 (kN/m) 4m hinge w

A: A beam is given, we need to analyse the beam i.e. finding reactions, axial force diagram, shear…

Q: STA BS HI FS IFS ELEV BM-a 1.24 235.75 234.51m TP- 1 1.11 233.46 3.40 232.35 1+00 4.6 228.86 1+25…

A: At turning point we have both fore sight and back sight. Reading is more means , staff is in lower…

Q: 2. Complete the following set of profile level notes and show the customary arithmetic check. Plot…

A: To Compute Complete the following set of profile level notes and show the customary arithmetic…

Q: • Find the tensions in the ropes that hold a 100N box. The ropes are considered weightless and are…

A: As per bartleby expert guidelines, we are allowed to solve one problem at a time. I am solving first…

Q: For the following orthographic projection, presented in Third Angle projection: • Draw an isometric…

A:

Q: Show the quadrants of a circle and within the circle show  S 30° W

A:

Q: Example - : The bearings of a closed traverse ABCD are as under. Calculate ncluded angles and apply…

A:

Q: Is there any other device available for measuring height of water level by replacing hook guage?

A: Hook guage  is used to measure  the water level to find evaporation Evaporations also measured with…

Q: PROBLEM 1 Determine the x- and y-coordinates of the centroid of the shaded area. y 0 0 ♡ 100 y = 1+1…

A:

Q: BEGO AV 6 MM CM X 2 2 5 24 INCH Styles Title 1 No Spac..... Question 2: Given that this soccer field…

A: Given Goal to goal distance = 100 m Required  Representative factor,RF of image

Q: Determine the y-coordinate of the centroid of the shaded area. 0.37h 54 --x Answer:F =

A: To find y coordinate of centroid

Q: Use the CAD drawing below and determine distances A and B to the nearest hundredth inch. + 2 A = O O…

A:

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: 2. Determine the member end moments and reactions for the frame shown in the figure by using…

A:

Q: P A plank 10 ft long is placed in a horizontal position with its ends resting on two inclined…

A:

Q: How do I find the horizontal analysis

A: Horizontal Analysis of financial statements is an analysis method that represents the changes that…

Q: Kindly answer with complete details use 3 decimal places, kindly provide neat solution to find the…

A: Given:- To find:- Total F and location from the top

Q: What is the torque, if a shaft of 200 mm diameter can transmit safely and the shear stress is not to…

A: Shaft diameter d=200 mm, Maximum shear stress- τmax=50 N/mm2. To Find- The value of the torque T.

Q: Complete the notes, find the elevation of point A and state the error in the network. Determine the…

A: HI= Elevation +BS Elevation= HI-FS

Q: In Fig. 8.32 two tunnels AB and EF are being driven forward until they meet in order to accommodate…

A: Given data:- Bearing AB=15°00' Bearing EF=265°00' According to the given figure, AB and EF meet at…

Q: Determine the y-coordinate of the centroid of the shaded area shown 7" Parabolic. 3" 0 0 5" -x

A:

Q: FIND THE SOLUTION (D3+7D² + 19D+13)y=D0 where x=0, y=o y'=2, y" = -12

A:

Q: convert -0.009 °F/ft to °C/100m. Please provide the full dimensional analysis

A:

Q: Please answer part C A = 150mm^2 E = 200GPa

A:

Q: 90 80 70 703 E.60 E50 40 E 40 30 E20 10 ) simple vertical staff gauge.

A: A staff gauge is used to measure water surface elevation or any another surface elevation.

Q: E Listen Profile Level Notes: The elevation of BM A = 522.17' BS (plus sight) on BM A = 9.25' IFS…

A: Required :- elevation of the STA 0+00?

Q: As shown in Fig. P-540, two blocks each weighing 20 kN and resting on a horizontal surface, are to…

A: Given ,    We have Two 20 KN blocks on each side.  Angle of friction = 15° Our aim is to calculate,…

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Q: 2. Find the force in members BC, BE, EF using the method of section. Show the free body diagram with…

A: Above given truss we have to find force in member EF, BC & BE by using method of section

Q: Calculate the vertical index difference and vertical angle in Tab

A: Station Target Vertical position Vertical dial reading O A L 78o32'12'' R 281o27'54'' B L…

Q: Q: From fig (1) calculate the elevations of marked points then draw the profile by hand (you can use…

A: To find RL of station

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.