Q/ Discu Second
Q: tarting at rest, a hydroplane accelerates at a = 0.8t for the first 10 seconds and then accelerates…
A: Given:The acceleration is The acceleration after is
Q: 50 MPa 60 MPa 100 MPa α ให้ 70 MPa
A: Given -To Find-
Q: A cylindrical tank is resting horizontally on the ground (the circular faces are vertical). The tank…
A: There are two types of forces that act on a circular surface: one type of force is radial force and…
Q: Calculate the enthalpy of propane in kJ/mole at 1000K assuming a representative specific heat value…
A: Given Specific heat, CP = 128.7 J/mole.K Temperature, T1 = 298 K T2 =…
Q: A manometer with water as in Figure 1.1. working fluid is connected to an air duct as shown
A:
Q: The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and…
A:
Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.
A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…
Q: For the compressor shown in the following figure, find the position of the piston with respect to…
A:
Q: Determine the magnitude of the resultant force and its direction, measured counterclockwise from the…
A:
Q: Differentiate clearly between tidal stream and range powers, and prove that. the mean power produced…
A: Tidal stream power : The power that is generated using the kinetic energy of a moving water is known…
Q: Determine the magnitude and location of the equivalent hydrostatic force acting on the circular gate…
A:
Q: 04: Complete the secetion of the reciprocating pump (shown in figure.2) by adding the details of the…
A: Gear box in the reciprocating pump The purpose of the gearbox is to convent rotating energy to…
Q: Determine the internal shear force at point C Express your answer to three significant figures and…
A:
Q: В |C O2 4 D 3 A E (201 5 F D 6 H at c I G Needle
A:
Q: Dimensions in mm Determine the magnitude of the force (in N) of the x-component of the internal pin…
A:
Q: 0.-A0"eQRT) 11) The value of Q can be confusing and different interpretations may arise. Explain…
A:
Q: 3. FBD for AK to determine the internal forces on K: forces/reactions on the AK; a. There are b. Sum…
A: In this problem, it is asking for question (3) so we will provide the solution for question (3)…
Q: Air enters a compressor operating at steady state at 105 kPa, 300 K, with a volumetric flow rate of…
A:
Q: he Lookout Hills gravitational slope-deformation feature in Bonne Bay, western Newfour plume of rock…
A: 306m wave height has been found in norris point.
Q: In the figure, aluminum [E = 68 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…
A:
Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…
A: Given data Reduction ratio = 2.32 Input torque = 100N-m Input speed = 3000rpm Efficiency = 98% Find…
Q: Airplane A is flying horizontally with a speed of 237 km/h which is increasing at the rate of 6.3…
A:
Q: 6.51 page 330 Determine the force in members DE and DF of the truss shown when P = 20 kips. F 7.5 ft…
A:
Q: Determine the force in member EF of the loaded symmetrical truss. Assume no horizontal reactions at…
A: Solution: Given Data: Horizontal reaction forces at A and C are zero. To Find: The force in the…
Q: Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and…
A: Volume for each action:Cyl. A extends DE = 65 cubic inCyl. A retracts DR = 62 cubic inCyl. B extends…
Q: Problem 9: A train of length 100 m is moving at a constant speed of 10 m/s. A second train, also of…
A:
Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…
A: Since you have asked only specific question so i answer only the subpart i for you. Given Data The…
Q: A square steel plate is perfectly insulated above and below, so the only heat flow is through the…
A: Given: To find: Temperatures inside the steel plate
Q: The figure (Figure 1) shows a model of a crane that may be mounted on a truck.A rigid uniform…
A:
Q: An engineer is making an estimate for a home owner. This owner has a small stream (Q = 0.05 m³/s)…
A: The given information in the problem is represented in the following attached image:
Q: For the mechanisms shown below determine the number of links, full joints, half joints and the…
A: The solution is provided below.
Q: A compound steel [G = 80 GPa] shaft consists of a solid 92-mm-diameter segment (1) and a solid…
A:
Q: F5-1. Determine the horizontal and vertical components of reaction at the supports. Neglect the…
A:
Q: Question 13 Solve the problem. Find the work done by a force of 200 pounds acting in the direction…
A:
Q: A 10-kg sack of flour slides down the smooth ramp, as shown in the figure. If it has a speed of 2…
A:
Q: solve the following explaining the steps please
A: Step 1: Step 2: Step 3: Step 4: solution is given above
Q: Match the given functions with the components of a wind turbine. Connects the rotor hub to the gear…
A: a) Main Shaft connects the rotor hub to the gearbox.
Q: Using the Method of Joints, determine the force in each member of the truss, and state if the…
A:
Q: Please write what each line of G- code means for each line. Thanks
A: G codes representation in the given program
Q: with the VSR
A:
Q: 4-3. The motion of the rigid body m is such that the point A moves in a circular path of 1-in.…
A: Given: To find: Velocity and acceleration polygon
Q: 50 kg Mạ - 3 ft- - 3 ft | 200 lb · ft Collar 4 ft B 12 Smooth surface Fig 1
A: Given-Data:- Force=50kg=110.231lb To-Find:- Reactions on the bent rod
Step by step
Solved in 2 steps
