Q: Determine the absolute maximum shearing force and bending moment in a simply supported beam of 50 m span due to series of four moving concentrated loads as shown below. 20 kN 20 kN 30 kN 30 kN t. Hur pt 6 m 6 m 50 m 十

Q: Determine the absolute maximum shearing force and bending moment in a simply supported beam of 50 m span due to series of four moving concentrated loads as shown below. 20 kN 20 kN 30 kN 30 kN t. Hur pt 6 m 6 m 50 m 十

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum shearing stress on the beam in MPa.
A reinforced concrete girder having a simple span of 11.18 m carries a superimposed dead load of 56.79 kN/m and a uniform service live load of 54.84 kN/m. The beam also carries a service concentrated %3D load of dead load (PDL = 31.31 kN) and live load (PLL =32.73 kN) at %3D quarter points (see figure below). The beam has a width of 490 mm and a depth of 798 mm. Use unit weight of concrete = 23.6 kN/m3 %3D PDL POL PDL PLL PL P LL L/4 L/4/ 11 L/4 Calculate for the maximum factored moment of the beam in kN-m. USE 2015 NSCP.
A reinforced concrete girder having a simple span of 10.97 m carries a superimposed dead load of 23.11 kN/m and a uniform service live load of 65.89 kN/m. The beam also carries a service concentrated load of dead load (PDL = 35.62 kN) and live load (PLL = 33.00 kN) at quarter points (see figure below). The beam has a width of 401 mm and a depth of 624 mm. Use unit weight of concrete = 23.6 kN/m³ %3D PDL PDL PDL PL PLL PLL L/4 L/4 /TTT7 L/4 Calculate for the maximum factored moment of the beam in kN-m. USE 2015 NSCP.
If the overhanging beam is made of wood having the allowable tensile and compressive stresses of 4 MPa and 5 MPa, determine the maximum concentrated force P that can applied at the free end. 2m O2.89 KN 3.52 KN O 1.22 KN O2.60 KN B 150 mm- 125 mm 200 mm 25 mm 25 mm
Solve the following problem 1. Compute for the maximum moment under each load when the system of moving loads cross a 10-meter simple span. |10 KN 15 KN 2p KN 6 m 3 m
4.) Five planks (4@ 40 x 40 mm and 1@ 40 x 380 mm), are joined together to form the l-section shown. Find the load (p in kN/m) this beam can carry on a span of 4 m, distributed over its length if the permissible stress in bending is 12 MPa and in shear 0.8 MPa. 40 mm B ww 08E ww 00€
A reinforced T-beam has an effective depth of 650 mm and is reinforced with 6-25 mm diameter bars. The web width is 330 mm and has a flange thickness of 120 mm. The beam has a span of 6.2 m and has a spacing center to center equal to 2.5 m, fc’ = 21 MPa and fy = 350 MPa. Compute the nominal moment capacity of the beam for positive bending in kN m. Express your answer in one decimal place.
Example 6.14. The central bottom chord member of roof truss is 4 m long, carries an ariol tension 250 kN and supports a moveable differential chain hoist of 4 kN capacity including impact. The member is composed of 2 angles 100 mm x 75 mm x 10 mm @ 13 kg/m with the longer legs up and placed back on either side of 10 mm gusset plates. The outstanding shorter legs at the bottom provide necessary track for the hoist. The angles are tack riveted at 1 m centers with 20 mm dia. rivets. Check the efficiency of the section provided. The permissible tensile stress in axial tension and bending are 150 MPa and 165 MPa respectively. The permissible stress in From whi 3300 compression for flangeless beams unsupported laterally may be taken as N/mm, subject 1/b to a maximum of 140 N/mm, where 1 = unsupported length of the member andb is the combined thickness of the angles.
Determine the support reaction forces of each given beam.
A simply supported span (middle span) of 6-m length with double cantilever of 1.5 m at each end is loaded as shown below. There is a concentrated moment of 6 kN-m acting at the tip of the left cantilever and a point load of 3 kN acting at the tip of the right cantilever. A concentrated force P = 10 kN is acting at the mid-point of the middle span. In addition, there are two partial uniform load of 5 kN/m acting on the middle span as shown below. The middle span has an I-section, of which the value of the moment of inertia I is given. The dimensions of the two flanges and the vertical web are also given. The right cantilever has a T-section. The dimensions of the top flange and the web are given. P = 10 kN 5 kN/m A B 3 kN 200 mm 5 kN/m 200 mm 6 kN-m S mm S mm 10 mm 2 m 1 m 2 m B 250 mm 250 mm 1.5 m 6 m 1.5 m S mm Section A-A **- 10 mm Section B-B left cantilever middle span right cantilever I= 6.67 x 10 ^7 mm^4 a.) Calculate the maximum bending stress of the middle span and plot the…
A B -2 m- 4 kN C 2 kN D 1m 6 m- (a) A 6m long beam ABCD is loaded as shown above and rests on foundation material (soil) that exerts a uniformly distributed load on the beam in response to these loads. Draw the free body diagram for the beam ABCD and determine the magnitude of the uniformly distributed load generated in the foundation material. i). ii). Draw the shear force and bending moment diagrams for the beam ABCD. If the maximum uniformly distributed load that the foundation material can carry is 7.5 kN/m, what loads can be applied at B and C?
6