Q// Design a synch. FSM with 2-i/p: X1 & X2 & one o/p- z. The machine required to detect the occurrence of the sequence of pairs of inputs: "00, 00 11, 10" on the two inputs & to give an output=1 during the final combination of a detected sequence. Note: 1. Using Mealy & Moore model. 2. Using implication chart to reduction. 3. Find the FF i/ps from the excitation table.

Q// Design a synch. FSM with 2-i/p: X1 & X2 & one o/p- z. The machine required to detect the occurrence of the sequence of pairs of inputs: "00, 00 11, 10" on the two inputs & to give an output=1 during the final combination of a detected sequence. Note: 1. Using Mealy & Moore model. 2. Using implication chart to reduction. 3. Find the FF i/ps from the excitation table.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

question 3B Construct an excitation table to enable implementation using J-K flip-flops and a Next State Decoder.
Review the image and provide correct solution!
Cl. Consider the designing of a synchronons circuit to detect the sequence 1100. The circuit has a single input x, and a single output z. The output is logic-1 whenever the input sequence 1100 is detected, logic-0 otherwise. Note that overlapping sequences are allowed. Answer the following questions: kel a Complete the following state diagram of the circuit SO SI S2 S3 S4 b. Draw and ill the state table of the circuit. Write the equations of the state variables and the output Z.
3. a) Draw the complete Moore Model state diagram for a sequence recognizer with input x which is a serial input of l's and 0's. It has 1 output z. z=1 iff the last 3 digits on the input are 0 10 AND must NOT overlap previously recognized sequence. A sample input / output might look like this: X= 10 10 1 0 1 0 0 0 1 0 0 1 0 1... Z= 0 0 0 10 0 0 1 0 0 0 1 0 0 1 0... b) Draw the corresponding Moore state table for the state diagram in part a).
6. Assume that we are working with a sequential circuit that takes a single input X, and in turn manipulates a JK flip flop and a D flip flop. It is pictured below. Draw the characteristic table (i.e., the extended truth table) for the circuit, using the column headers in the order X, D(t), JK(t), D(t + 1), JK(t + 1), where t and t + 1 refer to the value output on the Q line in the current cycle and the next cycle respectively. You can assume that the clock signal is being passed to the flip flops on each clock tick (i.e., in the normal fashion). X D 08 J >C K Q ?
Give the function f = x1· X2 · X4+x2 ·X3 · T4 + ¤ī • F2 · T3, a realization direct in an FPGA with LUTS with three inputs requires four LUTS. Show how it can be done using only 3 LUTS of three inputs. Mark the performance of each LUT with an expression representing the logical function that it achieves.
Using Verilog continuous assignments or VHDL signal assignments, write a description of the circuit specified by the following Boolean functions: Out_1=(A+B′)C′(C+D)Out_2=(C′D+BCD+CD′)(A′+B)Out_2= (AB+C)D+B′CWrite a testbench and simulate the circuit’s behavior.
i need the answer quickly
The figure below shows a digital circuit with three inputs (A, B, C) and three outputs (X2, X1, X0). The circuit is composed of the following components: . 74LS138: 3-to-8 line decoder. 74LS151: 8-to-1 multiplexer. 74LS20: Dual 4-input NAND gate. 74LS08: Quad 2-input AND gate. 74LS04: Hex inverter. A U1 YD ۲۱ 1 U2 A c 12 B Y3 хо Y4 Ε Y5 T4L520 12 YB YT с U3 741513 U6:A 300 X1 32 X4 35 11 хт C E 745151 U4 A 74L504 U6:B 74L515 US:A 741503 74L504 X1 U7:A x2 745532
DO NOT COPY FROM OTHER WEBSITES Correct and detailed answer will be Upvoted else downvoted. Thank you!
a) Create the truth table for all possible combinations of inputs (A, B, C) and their corresponding outputs (X2, X1, X0). ABC X2 X1 XO 0 0 0 0 0 1 0 1 0 0 1 1 1 0 0 1 0 1 1 1 0 1 11 b) Implement the circuit in Verilog using any modeling technique of your choice. Ensure that your implementation considers the propagation delays (as mentioned in the table below) specified in the datasheets of each component [Set time scale to Ins/1ps]. Verilog Code
please help