Answered: Q/ Briefly explain how these factors…

Q/ Briefly explain how these factors affect wettability 1-the pore size 2- the surface roughness 3-the adsorptive properties of minerals.

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter21: Structure And Bonding In Solids

Section: Chapter Questions

Problem 42P

See similar textbooks

Similar questions

The microstructure of spheroidite takes the form of spheres. Explain why?
Describe the difference between vitreous silica and soda-lime glass. What are some advantages and disadvantages of each of these types of glass?
The density of tantalum at 20oC is 16.69 g/cm3 and its unit cell is cubic. Given that the first five observed Bragg diffraction angles are θ =19.31o, 27.88o, 34.95o, 41.41o and 47.69o, find the type of unit cell and its length. Take the wavelength of the x-ray radiation to be λ =154.433 pm.
7. Consider these three labelled specific volume vs. temperature plots that may be displayed by various types of materials. Indicate the one, which best describes the behaviour expected from PP with a spherulitic structure. (a) sp. volume (b) (c) temperature
What is the density of atoms/nm^2 on the (110) plane of a zinc blende lattice with lattice spacing 0.489 nm. Three significant digits, fixed point notation.
1/ What is meant by the term coordination number in the structure of a solid? 2/ How does the coordination number depend on the structure of the metal?
a) Draw rock salt unit cell of NaCl and give the coordinates (u,v,w) describing the positions of all the atoms in such a unit cell. b) Calculate the structure factor |F_hkl|^ 2 for such a unit cell for x-ray scattering from a given set of crystallographic planes (hkl). c) Which reflection peaks have the lowest and highest intensities and why
1. What are the principal natural processes that affect the petrophysical properties of sedimentary rocks? 2. As shown in Table 1.1, the total bulk chemical analysis of rock samples is clearly different from the surface analysis. What effect does this have on the rock properties?
The unit cell of strontium titanate SrTiO3 is depicted on the left in the figure below showing the crystal structure as confirmed by X-ray diffraction experiments. The lattice constant is a - 3.9 × 10-¹0 m. A typical X-ray powder diffraction spectrum is displayed on the right. The wave length of the X-ray beam (Cu-Ka radiation) is λ = 1.54 × 10-¹⁰ m. Unit cell of SrTiO3; Sr atoms are shown in blue, Ti in black and the oxygen atoms are in red. Normalized intensity (a.u.) (001) 20 (011) 30 (III) 40 (200) (210) 50 (211) (220) (300) 60 20 (degrees) 70 (310) (311) >(222) (320) 80 90 (17) 100 X ray powder diffraction data for SrTiO3; the plot shows an overlay for two different SrTiO3 samples. [L. da Silva et al, J. Nanomat., doi:10.1155/2012/890397] a) Identify the Bravais lattice of SrTiO 3and specify the basis for the primitive unit cell shown in the figure. b) Explain how the Miller indices (hkl) describe a family of lattice planes. State a set of possible reciprocal lattice vectors. c)…
Describe the features of Network Covalent Atomic Solids, Carbon and Silicates?
Name the three (3) unit cells commonly found in metal structures and briefly explain the method of their formation.
Calculate the concentration of vacancies in copper at room temperature (25 °C). What temperature will be needed to heat treat copper such that the concentration of vacancies produced will be 1000 times more than the equilibrium concentration of vacancies at room temperature? Assume that 20,000 cal are required to produce a mole of vacancies in copper. The lattice parameter of FCC copper is 0.36151 nm.