Q: A siane shown in Figure has a weight of 10 AN. If the coelliciont of friction is 0.35 at the surface contact, delemine the minimum force P acodod to remove the wedge Wedge

Q: Dotermine all fur ce truss Shown mem bers of the

A:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A: given; AB=8.6'BC=3.6'angle(α)=?lets take tension force in member AB=TABlets take tension force in…

Q: If the applied load F has a size of 300 N, find the tension in the 3 supporting ropes 34 2 2ft 5# 45…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: 3 300N Fi= 100N 45 120 50 60 20 5=200 N De termine Hhe reso ltant force and the Coor di nale…

A:

Q: :O38/ Given the followtng data, the chear stress value at segment BC is G 80 GPa Diameter= 2e m 沙…

A: Find the shear stress in segment BC.

Q: Q2/ Analy ze the forces shown in (Figure 2) into their components. F1 F2 F3 Figure 2

A: We have to figure out the horizontal and vertical components . for that we need to figure out the…

Q: 1. Rectangle A = bh bh b. hb 12 hb ly = bh

A:

Q: Two tension forces are applied to the top of the tower as show wire is also attached to the top of…

A: Given data is We have to find the Tension in the wire AB such that the resultant force is only in…

Q: What is the position of the center of mass of the bar, measured as distance x from the bar's left…

A:

Q: Three force are a s teel Plasfe a c ting on with 4m Leng th by um width Shown in figure The se three…

A:

Q: OD 3m 16 my 2 m Figure 3

A:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A: Given data as per the question The load applied at point A =440 lb

Q: Determine the angle θ (degrees).

A:

Q: The screw of the clamp exerts a compressive force of 500 N on the wooden blocks. The cross section…

A:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A:

Q: Blocks D and E weigh 5 lbf each. Block E weighs 8 lbf. Find the sag, s. 4 ft 4 ft

A:

Q: Q3 Derive the relations 2²F' Cy = -T ƏT? and Cp 3 —Т ƏT² P

A:

Q: Find the angle a. A 175 lb α Answer: a = i 8.6' B 3.3' 54° O

A: We have to determine angel α

Q: Ţ Į 100 Mpa 75 Mpa 150 Mpa If the element shown was rotated 60° CW Find: (α)σχ' (b)ay' (c)tx'y

A: (a) To find: The value of principle stress σx'. Given :  The element is rotated by θ=60° counter…

Q: I want the force for A and B by using the centroid or solve it by the right way

A:

Q: The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to…

A: Given: To find: Resultant shear force at C in y direction Resultant shear force at C in z…

Q: board cables 30° hinge canal Figure 3

A:

Q: solve for the reactions at A and B

A:

Q: A CIRCULAR STEEL SHAFT (G= 80 G Pa ) Is COADED Bu Two TORQUES. AT Points A Awo C As SHOWN. FiNo: THE…

A: Given data, G= Modulus of elasticity of the shaft=80GPa =80x103 MPa T = Torque applied =1000x103 Nmm…

Q: Find the height to be raised P.E=2442.11J

A: Given data : m=Mass g=Acceleration due to gravity P.E=Potential energy   Required : height to be…

Q: 0. Determine the magnitude g the Resuftot. b. Determine the Pokce g the Reacionsat A C. Determine…

A: Solution:   The magnitude of the resultant and the support reactions at A and B are calculated…

Q: Find the force in the member EC of the trus ölkn in the figure D2 AN 4 kN 2 kN 10 m 10 m (A) 8 KN…

A:

Q: The sign has a mass of 1200 N with center of mass at G. Determine the x, y, z components of reaction…

A:

Q: Q/Determine Hthe x and y Components of Fi and tz acting. on the beom Shown in figure below- = l00N…

A: Given data: F1=300 N F2=100 N θ1=45° θ2=30°

Q: 2m 3m 30° D.

A:

Q: 1 m GC 2 m A 2 m 1.2 m- QD 1 'm •G 1.2 m B

A:

Q: Find the Rentant ot the force Syshem Sho in Fig and Located w.r.t. point A? 250 150N 200 N

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.