Q: A building has the following calculated cooling loads are 310 kW sensible heat and 100 kW latent heat. The space is maintained at the conditions of 25°C DBT and 50% RH. Outdoor air is at 28°C DBT and 50% RH and 10% by mass of air supplied to the building is outdoor air. If the air supplied to the space is not to be at a temperature lower than 18°C, find:

Q: A building has the following calculated cooling loads are 310 kW sensible heat and 100 kW latent heat. The space is maintained at the conditions of 25°C DBT and 50% RH. Outdoor air is at 28°C DBT and 50% RH and 10% by mass of air supplied to the building is outdoor air. If the air supplied to the space is not to be at a temperature lower than 18°C, find:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the efficiency of the cooling tower with following working conditions: The air inlet dry bulb and wet bulb temperatures are 24.50Cand 16.80C respectively. The air outlet dry and wet bulb temperatures are 25.60Cand 170C respectively. The water inlet and outlet temperatures are 20.80Cand 190C respectively.
A heat engine input heat 20 kJ and gives an output of 6000 J. Determine the thermal efficiency and rate of heat rejection. Select one: O a. 50% and 26 KJ O b. 30% and 14 KJ O C. 42.85% and 14 KJ O d. 30% and 26 KJ
What is the maximum theoretical COP for a freezer that is maintaining a temperature of -10 degrees celcius and exhausting heat to a kitchen that is 20 degrees celcius?
An air-conditioning absorption system has an evaporator capacity of 350 kW with a COP of 0.90 operating at a temperature of 25 C with a condensing temperature of 35 C. The same cooling tower was used to reject the heat from the condenser and the absorber operating 45 C & providing 1 kg/s of water plus lithium bromide solution to the generator. Consider the heat rejection ratio of condenser to evaporator is 1.05, Determine the following: 1. Heat given by the generator & the size of condenser in kW 2. Leaving condenser & evaporator enthalpies & the mass of refrigerant water flowing from the generator to the condenser then to the evaporator & to the absorber (using evaporator heat balance). 3. Weight of lithium bromide in kg/s, concentration in percent & enthalpy from the absorber to the generator in kJ/kg 4. Enthalpy from the generator to condenser in kJ/kg (using condenser heat balance) & concentration in percent & enthalpy from generator to absorber…
A homeowner is trying to decide whether to heat with a furnace rated at 95% efficiency or by an electrically powered heat pump. She lives in a town where electricity is produced by a coal-fired power plant that claims to operate with 1st law efficiency that is 55% of the Carnot limit. The heat pump's CoP is advertised to be 40% of the Carnot limit. For what range of outside temperatures To would the 2nd law efficiency of the furnace be greater than that of the heat pump? Assume T+ = 400°C, T- = T= 40°C. %3D
In refrigeration systems is it possible to change the refrigerant? If you alter the type of refrigerant whattype of changes is required for your refrigerator design? Compare two different refrigerants and discussyour proposal about the design change.
Provide complete solution and detailed diagram. A refrigerator is to remove heat from the cooled space at a rate of 300 KJ/min to maintain itstemperature at - 8oC. If the air surrounding the refrigerator is 25oC, determine the minimum powerrequired for this refrigerator? A. 0.263 kw B. 0.473 kw C. 0.623 kw D. 0.984 kw
Consider the refrigerator shown in Figure. If the compressor consumes 850 W of power and the COP of the refrigerator is 2.5 determine. The mass flow rate of the refrigerant The rate of heat rejected to the kitchen air Condenser Expansion Xvalve Wn Compressor Evaporator 100 kPa 100 kPa x0.2 -26°C
Asking second time , Strictly don't use chatgpt. I need to understand the concept,give detailed solution in Handwritten format.
Heat Engine you are an engineering consultant who has been tasked with providing power to a remote village. After some initial evaluation it was determined that a simple four-device heat engine with water as the working fluid is the best option to produce electricity at the location. Natural gas and wood are abundantly available as a fuel source and 400 kW of power is needed. Design a heat engine to meet the stated requirements.
A building is being heated through the help of a Carnot heat pump and is required to be maintained at 20 degrees C always. When the temp outside drops to -10 degrees C, the rate at which heat is lost from the building is 25kW. What is the minimum electrical power required (kW) in order to drive the heat pump?