Q-5 Consider an S-590 alloy component as shown in following figure that is subjected to a stress of 200 MPa (29,000 psi). At what temperature will the rupture lifetime be 50A h?| (A is the 4th digit of your student number, from the left)

Q: LESSON: AUTODESK AUTOCAD Choose from the choices:

A: The broken line is used to draw the large drawings which are not possible to draw on the sheet,…

Q: Convert to isometric drawing mark point A as the lowest point

A: use a 30-60 triangle to create the isometric  figure ng follow the left, front and top illustration…

Q: TS DIAGRAM

A:

Q: Figure 1. Length of line AC? Zradis 8.33" 10 5.83" 9.72" 11.33" Figure 1. Value of angle <BAC in…

A:

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: "Given the figure, what is the positive direction of Block B?"

A: Explanation: We take positive in downward direction because acceleration due to gravity act in…

Q: Give the name of the following graphic symbols or Draw the graphic symbol according to the following…

A:

Q: Convert the octal number 23228 to its hexadecimal number equivalent, (base-8 to base-16).

A: Steps of Conversion: The simplest way is to convert the octal number into a decimal, then the…

Q: How did you get theta =45?

A: Consider following given figure of a structure.here we need to determine the angle between member DE…

Q: Give the name of the following graphic symbols. M) (a) (b) (c)

A: Given: Name the graphical symbols.

Q: where is the T-S diagram

A: Rankine Cycle is a ideal cycle for producing net work output in thermal power plant where water is a…

Q: Show dimension numbers according to a well-balanced scheme! Top Front Right Side Figure 1

A: The Answer is Below

Q: L t C Determine the moments at fixed ends 'a' and 'd' ?

A:

Q: Using the drawing below identify th mistake on dimensioning rules and write the correct method to…

A: According to DG&amp;T standards, there are 5-dimensional mistakes that are highlighted in the fig…

Q: A container fill with an unknown liquid has three holes as shown in Figure Q1 (a). Determine the…

A:

Q: 2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits…

A:

Q: y 4+B 5+C 2 3. 1.Find The size of the area number 1 (triangle) 2.Find The center of the numbered…

A: Given data: h1=3+Ab1=4+B Need to determine the centroid and area of the shape 1.

Q: gedem +x) 1+2) Circle the letter corresponding to the view on the right that shows the result of…

A: First, rotates the object along the y-axis in an anticlockwise direction then again rotates along…

Q: can you help me understand this better. I am going to reproduce this drawing by using Creo. And i…

A: Here's a breakdown of the GD&amp;T symbols used in the image:Datum symbols: A datum is a…

Q: E 12.5 m C А 8 m 5 m

A:

Q: What is the name of the highlighted symbol?

A: Dear student, I was the only one who solved this question.

Q: Draw the orthographic Projections of given object.

A: Required orthographic views of the given isometric view are drawn on grid paper. 1 Grid = 1 Unit

Q: n the figure, front (1st picture) and left (2nd picture) views of a machine part are given. Based on…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: The tool starts at point P1 (X-50.0,Y-15.0) and goes around the part counterclockwise. It then goes…

A: CODES USED IN THE PROGRAM G01 -LINEAR INTERPOLATION G03- CIRCULAR INTERPOLATION , COUNTER CLOCK WISE…

Q: A pyramid ABCD, the heud poiut A(2,5,4) and base points B(2, 0.5,0), C(O.5,2,0 and D(-1, o, 0).…

A: Given data The points of the given pyramid are  A(2,5,4) with base points B(2,0.5,0) , C(0.5,2,0)…

Q: Q2 (a) Figure Q2 (a) shows two vectors FA and Fa represent the forces exerted on the pulley by the…

A:

Q: 1. Give the rectangular coordinates of the point C (p = 4.4, q = -115, z = 2). 2. Give the…

A:

Q: Write all the commands steps of the AutoCAD software to reach the drawing of the figure below all…

A:

Q: For the following figure in writing the dimensions if we write the symbol R Instead of the value of…

A: For the following figure in writing the dimensions if we write the symbol R Instead of the value of…

Q: An exponent, such as the 4 in the expression 94, means: the number of times the number before the…

A: It is required to determine value of 94

Q: sketch the 2d figure using autocad and colour the hatching and reference lines

A:

Q: Draw Front and Side and top with all dimensions please

A: According to the question,A  3-D object is provide, we need to draw three projection views of the…

Q: 8ェ4 2 w/

A: the value of  (4x-4)/2= (4*(-1)-4)/2= -12/2 =-6

Q: Question 2 A point P in space is defined as P= [3, 5, 4] attached to a frame (,,a) Compute the end…

A: Let's start with the first transformation: rotation of 45∘ about the n-axis.###(i)  Given a point P…

Q: 20 30 40. -30 100- Draw the three projections of the following figure 60

A:

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.