Q/ 30-kVA, 2200/220-V, 50-Hz distribution transformer is tested for efficiency : and regulation as follows O.C. test( Low voltage side ) : 220 V 4.2 A, 148 W 10.5 A, 360 W S.C. test ( Low voltage side ) : 86 V نقطتان )2( Equivalent reactance referred to primary & referred to * secondary. .ohm, .ohm 6.71 , 0.0671 9.51 , 0.0951 7.51 , 0.0751 8.51 , 0.0851 نقطتان )2( The working current and resistance component of no-load are.. .amper, . .ohm 0.87, 556.89 0.67, 436.89 0.76, 326.89 0 57 236 89

Q/ 30-kVA, 2200/220-V, 50-Hz distribution transformer is tested for efficiency : and regulation as follows O.C. test( Low voltage side ) : 220 V 4.2 A, 148 W 10.5 A, 360 W S.C. test ( Low voltage side ) : 86 V نقطتان )2( Equivalent reactance referred to primary & referred to * secondary. .ohm, .ohm 6.71 , 0.0671 9.51 , 0.0951 7.51 , 0.0751 8.51 , 0.0851 نقطتان )2( The working current and resistance component of no-load are.. .amper, . .ohm 0.87, 556.89 0.67, 436.89 0.76, 326.89 0 57 236 89

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
Answer in short please i will like....
A single phase 220/6 Volt, 50 Hz transformer has a rated primary current = 0.5 A. its maximum efficiency is at load current = 15 A and equal to 94% at unity p.f. Its efficiency at rated load, 0.65 p.f. lagging is: 087.8%. 092.3%. 090.9%. O None.
Q6 Complete the answer : If connected .................... to the transformer changes, copper loss varies.
B/ Fill in the blanks: 1. The purpose of providing the iron core in the transformer is to 2. A transformer transforms... 3. Power transformers are designed to have maximum efficiency at 4. The transformer ratings are usually expressed in terms of menm
The turns ratio of a particular transformer is less than 1. Where would you expect to see this type of transformer? OI. A 0 0 0 0 0 Power Plant K Generation II. A and B III. B IV. B and C V. C VI. C and A A Station High-Voltage Power Lines Transmission B Substation C Distribution Power Lines ( .00 Industrial Consumer Commercial Consumer Residential Consumer Distribution
a single-phase transformer serves a 7.2kw resistive loadlocated 200 ft from the transformer. each conductor from the transformer to load has an impedence of (0.78+j0.052) ohms per 1000ft. if the voltage at the load terminal is 240v, the magnitude of the voltage (v) at the transformer secondary is most nearly:
Q5:Choose the correct answer from the given alternatives (answer five only) 1.In an ideal transformer, (a) windings have no resistance (b) core has infinite permeability (d) all of the above. (c) core has no losses 2. The primary and secondary induced e.m.fs. El and E2 in a two-winding transformer are always: (a) equal in magnitude (b) in-phase with each other (c) antiphase with each other (d) determined by load on transformer secondary. 3. In relation to a transformer, the ratio 20 : 1 indicates that (a) there are 20 turns on primary one turn on secondary (b) secondary voltage is 1/20th of primary voltage (c) primary current is 20 times greater than the secondary current. (d) for every 20 turns on primary, there is one turn on secondary. 4. A transformer has negative voltage regulation when its load power factor is: (a) zero (b) lagging. (d) unity (c) leading
High voltage engineering
Example 5 A 600 kVA transformer has a primary winding resistance of 0.62 and a secondary winding resistance of 0.002 2. The iron loss is 2.6 kW and the primary and secondary voltages are 6 kV and 330 V respectively. If the power factor of the load is 0.8, determine the efficiency of the transformer (i) on full load, and (ii) on half R.. load.
Full calculation with any assumption needed. All sub questions please as it is all related.
5. Write down the equations of a single phase transformer at no-load mode. Give the names of the resistances, reactance, e.m.f.'s, currents and voltages.