Q-3. A common Source E- MOSFET Amplifier with Voltage divider biasing with, Va= 24 V, R.= 3KO, R.= 100KN, R:= 18 KN. loe = 200 mA, Va= 4 V, Vesna = 2 V, g-= 23 mS, and V.ne = 25 mV.asTH[3](i) Draw the circuit diagram label all the necessary values(ii) Find the Q point.(iii) Find the peak output voltage.

Answered: Image /qna-images/answer/87ccc838-29aa-4809-811d-cdbb15c7768d.jpg

Q-3. A common Source E- MOSFET Amplifier with Voltage divider biasing with, Va= 24 V, R.= 3KO, R.= 100 KO, R= 18 KN. Iaa = 200 mA, Vas= 4 V, Vasna = 2 V, g-= 23 ms, and Vne = 25 mV. [3] (i) Draw the circuit diagram label all the necessary values (ii) Find the Q point. (iii) Find the peak output voltage.

Q-3. A common Source E- MOSFET Amplifier with Voltage divider biasing with, Va= 24 V, R.= 3KO, R.= 100 KO, R= 18 KN. Iaa = 200 mA, Vas= 4 V, Vasna = 2 V, g-= 23 ms, and Vne = 25 mV. [3] (i) Draw the circuit diagram label all the necessary values (ii) Find the Q point. (iii) Find the peak output voltage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1. (a) Using the hybrid-pi model with early voltage effect, compute the small signal voltage gain, Av, input resistance and output resistance for the CE BJT amplifier shown below. Vec = 12 V B=100 VELON) = 0.7V V = 100V R = 93.7k2 %3D E R=6 kN Rg=0.5 k2 C, E R2= 6.3 k2 Figure Q1(a)
34
III An n-channel MOSFET ID versus VDS set of characteristics is shown below. A common-source resistively loaded amplifier uses this MOSFET. The resistive load RL = 1,000 ohms and the drain power supply (VDD) = 3 volts. (a) Draw the load line over the l-V characteristics shown immediately below.. (b) What is the slope of the resistive load line? VDD =3 volts 6 mA 5 mA -+ R. 4 mA + 3 mA -t 2 mA 1 mA 3 V 4 V 5 V Vps
What is the average output power of an SSB transmitter rated at 100-W PEP?
2. The parameters of the transistor as shown in the figure below are ß = 100 and VA = 100V. a. Find the dc voltages at the base and emitter terminals. b. Find Rc such that VCEQ = 3.5V. c. Assuming Cc and CE act as short circuits, determine the small-signal voltage gain Av = Vo/Vs. d. Repeat part (c) if a 5000 source resistor is in series with the vs signal source. V+ = +5 V Rs = 100 £2 www Us Cc RB = 10 ΚΩ I= Iausmi 0.35 mA www RC -000 V=-5 V CE
The maximum junction temperature of a transistor is 150°C and the ambient temperature is 25°C. If the total thermal impedance is 1°C/W, what is the maximum power dissipation ?
Help
Common Gate MOSFET Amplifier has Select one: a. input is connected to the Gate and the output is taken from the Source b. input is connected to the Source and the output is taken from the Drain c. input is connected to the Gate and the output is taken from the Drain d. input is connected to the Source and the output is taken from the Gate 55 week 10 material Jump to... CE255/EE255 (01)- 16
Construct an approximate voltage transfer characteristic curve of the amplifier by filling up the table below using the large signal model of the transistor and plotting the results. VI (volts) vo (volts) -2.0 0.0 1.0 2.0 Remarks assume linear transition to saturation transition to cut-off assume cut-off VI 2.5 V 100 K Ţ Vo
For the p-channel JFET circuit in the Figure, the transistor parameters are: /oss = 2 mA, Vp = |1.75| V. (a) Determine Ipo and Vspo- (b) Give the small signal model (c) Determine the small-signal voltage gains Av = vo/vi QUESTION I: For the p-channel JFET circuit in the Figure, the transistor parameters are: Ioss = 2 mA, Vp = |1.75| V. (a) Determine Ipo and Vspo- (b) Give the small signal model (c) Determine the small-signal voltage gains Av = vo/vi VDD = 10 V Rg = 5 k£2 R1 = 90 kQ %3D Cc2 RL = 10 k2 R2 = 110 k2 ww
1. By using re model, draw the a.c. equalent circuit for the transistor amplifier shown in figure 1 Figure 1 i. ii. iii. iv. "Î Figure 2 R₁ C₁ V₁ R₂ 2. By using equalent circuit mention in 'part 1'. Write the mathematical expressions for followings, www m input impedence of the amplifier output impedance of the amplifier voltage gain of the amplifier current gain of the amplifier 3. By using h-parameter model, draw the a.c. equalent circuit for the transistor amplifier shown in figure 2. Assume that hre= high (∞), hoe = 0 and the rectance of capacitors C₁, C₂ and C3 is zero. Vcc Rc R₁ C₁ VBE RE R₂ +₁. Vcc Rc RE: C₂ C₂ Vo Vo R₁ R₂ Rc RE hie hfe = 38 ΚΩ = 10 ΚΩ = 4.7 ΚΩ = 2.2 kΩ = 1kΩ = 50
For the given Common Emitter NPN Amplifier, the transistor made of Germanium diodes, BDC-80, Vcc Rc-3.9 K2, RE-0.68 KQ. a) Name the type of biasing used in the above circuit? 1 = 16 volts, R= 62 KQ, Rz 9.1 K R, Rc Cs b) Find VE? Find VCE? d) Find Vc? e) What is the name of the capacitors C1, C3 and C2?