Q (2) - The following data pertain to a Francis turbine: Net head = 70 m, Speed= 700 r.p.m, Shaft power = 330 kW, Overall efficiency = 85 %, Hydraulic efficiency = 92 %, Flow ratio= 0-22, Ratio of wheel width to wheel diameter at inlet = 0.1, Outer diameter of runner = 2 x inner diameter of runner, Velocity of flow constant, Outlet discharge radial. The thickness of vanes occupies 6 percent of circumferential area of the runner. Determine: (i), Diameters of runner at inlet and outlet, (ii) Width of the wheel at inlet, (iii) Guide blade angle, and (iv) Runner vane angles at inlet and outlet.

Q (2) - The following data pertain to a Francis turbine: Net head = 70 m, Speed= 700 r.p.m, Shaft power = 330 kW, Overall efficiency = 85 %, Hydraulic efficiency = 92 %, Flow ratio= 0-22, Ratio of wheel width to wheel diameter at inlet = 0.1, Outer diameter of runner = 2 x inner diameter of runner, Velocity of flow constant, Outlet discharge radial. The thickness of vanes occupies 6 percent of circumferential area of the runner. Determine: (i), Diameters of runner at inlet and outlet, (ii) Width of the wheel at inlet, (iii) Guide blade angle, and (iv) Runner vane angles at inlet and outlet.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Francis radial-flow hydroturbine (inward) has the following dimensions: r2=2.00 m, r₁=1.30 m, b2=0.85 m, and b1=2.10 m. The runner blade angles are ß2= 66° and B1= 18.5° at the turbine inlet and outlet, respectively. The runner rotates at N=100 rpm. The volume flow rate at design conditions is 80 m³/s. Irreversible losses are neglected in this preliminary analysis. Calculate the angle a2 through which the wicket gates should turn the flow, where az is measured from the radial direction at the runner inlet. Calculate the swirl angle ai, where an is measured from the radial direction at the runner outlet. Predict the power output (MW) and required net head (m).
5): For the system shown below: 1-Find the water power of the turbine (PT) if the required power output is PE (take PE between 5-25 kN) and the turbine efficiency is n (take n between 75 to 98%) 2- Find the flow rate in the pipe AB. 3-Find the value of Z1 for operating this system (take Z2 between O to 20 m). * Pitot tube Piezometer. 0.3m 1.0m z1 22 T. Id= 200mm d= 100mm
Consider the figure below. The pump supplies water from reservoir A to reservoir B through the 500mm o pipe, 600m long. Using f = 0.02 and the hydraulic grade line shown, determine the following: a) power supplied by the pump, b) power loss by the turbine, and elevation maintained by reservoir B. El. 200 hfj El. 190 НЕ El. 180 hf, B El.100 A P TURBINE PUMP ANSWER: a. Power = 1557.828 kW, b. Power = 155.7828 kW c. Elevation of B = 170 m %3D
1. Water is following steadily through a 50 m long section of a horizontal 5-cm diameter stainless steel pipe. The water temperature is 15°C and the flow rate is 9 L/s. Determine: a.) The pressure drop over the pipe length [kPa]. b.) The head loss [m]. c.) The pumping power needed to overcome the pressure drop (assume a pump efficiency of 67%) [kW]. 9 L/s 5 cm 50 m
Determine the division of flow and head loss from A to B, if the given f=0.010 for all pipes. Note that the total flow is 10 cfs. L=4000ft D=16 inch B L=2000ft D=12 inch
The pipe connection shown has a series parallel connection. The rate of flow in the pipe 1 is 300 liters per sec. Assuming equal values of f = 0.02 for all pipes. Compute the discharge of pipeline 2 in cu.m per sec. Compute the discharge of pipeline 3 in cu.m per sec. Compute the discharge of pipeline 4 in cu.m per sec.
Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.
For the setup shown in the figure :
Problem1: A new coagulation water treatment plant is proposed to treat 0.1145 m³/s at an average temperature of 19 °C. The tank is circular, and the required water depth is twice the diameter. Using the following design assumptions: detention time=10s; velocity gradient = 800 s¹; impeller type: radial flow turbine with 6 flat blades and assume B-H/3. Determine a) The tank dimensions b) The impeller diameter knowing that the available diameters are 0.45 and 0.6 m c) The required input power
شمذنس Fluid mechanics
The commercial steel tube is then 100 m long and0.4 m in diameter. Calculate the height of the tower h, if the flow speed for7.95 m / s. Consider that losses are negligible and that losseswater temperature is 4 ° C
Question 1: For the setup shown in the figure: H = 20 m f = 0.0012 f = 0.0012 D = 250 mm D = 80 mm L = 50 m L = 50 m f = 0.001 D₁ = 150 mm L = 100 m A. Calculate Q in the 150 mm-diameter pipe B. If the NPSHR of the pump is 3 m. Is it feasible to use the pump? You can use: Patm-101 kN/m², and Pvapor = 3.17 kN/m² H₂ = 10 m Pump Q f = 0.0012 D=80 mm L = 50 m Q₁ = 0.2