Use the method of consistent deformations to determine the reaction components, and draw the shear force and bending moment diagrams for the beam shown in Fig.1 Q-1Use the method of consistent deformations to determine the reaction components, anddraw the shear force and bending moment diagrams for the beam shown in Fig.1.(constant EI)(20 marks)BLFig.1

Answered: Image /qna-images/answer/1106dc42-1684-4da5-ac7c-4f28a996cdce.jpg

Answered: Q-1 Use the method of consistent…

Q-1 Use the method of consistent deformations to determine the reaction components, and draw the shear force and bending moment diagrams for the beam shown in Fig.1. (constant EI) (20 marks) Fig.1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A thin walled member of 1000 mm long has the cross-section shown in figure. Determine the maximum torque which can be carried by a section if the angle of twist is limited to 10%. What will be the maximum shear stress when this maximum torque is applied? Take G = 80 GPa. 18 mm- 2 mm 40 mm-
A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as shown in the figure. Rod 1 is of copper, with a cross sectional area of 1cm?; rod 2 is of steel, with a cross sectional area of 1.5cm2; rod 3 is of aluminum, with a cross-sectional area of 2cm? Determine the stress in the rods it p = 6 tonnes.
A plane element in a body is subjected to a normal tensile stress in the x-direction of 84000 kPa, as well as shear stresses of 28000 kPa, as shown. What are the principal stresses? y 84 000 kPa 28 000 kPa 28 000 kPa X 84 000 kPa
EXAMPLE 4.1 Determine the deformation of the steel rod shown in Fig. under the given loads (E = 200000000 kN/m²) 600mm2 200mm2 100 kN 300kN 200kN 0.4m 0.3m 0.3m
6. In Fig. 6, a 1.5 m long cantilever beam with a circular cross section (R = 100 mm) and two symmetrically positioned longitudinal holes is loaded by a concentrated force P at its tip. The material is a titanium alloy with a 600 MPa maximum allowed working stress when bent. Find the maximum permitted vertical force P value. 1.5 m Radius= R = 100 mm Radius of hole =
The cross section of a composite beam that consists of 4-mm-thick fiberglass faces bonded to a 20-mm- thick particleboard core is shown in Figure P8.43. The beam is subjected to a bending moment of 55 N-m acting about the z axis. The elastic moduli for the fiberglass and the particleboard are 30 GPa and 10 GPa, respectively. Determine (a) the maximum bending stresses in the fiberglass faces and the particleboard core. (b) the stress in the fiberglass at the joint where the two materials are bonded together. 4 mm FIGURE P8.43 50 mm 20 mm 4 mm
A thin triangular plate ABC is fixed on side AB. The plate is strained such that all straight lines in the plate remain straight after deformation and that apex C is displaced to point C'as shown. Compute the following: a) the normal strains ex, ey and the shearing strain yxy at point C based on small deformation theory b) the normal strain at point A in the direction of AC based on small deformation theory c) the normal strains ex, ey and the shearing strain yxy at point C based on large deformation theory A 30° -200 mm. 3mm C" 1 I 1 1 60° 4mm
Internal tensile forces in a rod subjected to a uniaxial pulling load
At a particular point in a structural member a direct tensile stress of 60 N/mm² exists on a plane perpendicular to the longitudinal axis of the member while a direct compressive stress of 40 N/mm? occurs on a plane parallel to this axis; in addition shear and complementary shear stresses of 50 N/mm? act on these planes. If Young's modulus E is 200000 N/mm² and Poisson's ratio v is 0.3 calculate the direct and shear strains on these planes and hence, using a graphical method, determine the principal strains at the point, the maximum shear strain and the angle the plane of maximum principal strain makes with the longitudinal axis of the member. Finally, calculate the principal stresses at the point. Ans. E= 3.6x104, ɛ, = -2.9x104, Yy=6.5x10-4 ɛ1 = 4.95x10, 01 = 80.8 N/mm², o1=-60.8 N/mm. Ɛ11 =-4.25x10 Ymax=9.2x10-, 67.5°
Q.41 For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 2 44 4 4 4 2
In a body under triaxial state of stress, the principal strains at a point are 0, 500 x 106 and - 600 × 106 the maximum shear strain at the point is 1. 500 x 10-6 1100 x 106 3. 600 x 106 4. 550 x 106 2.
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 30 x 10 -3 mm while those at CD decrease 70 x 10 -3 mm in the 250-mm-gage length. Using E = 110 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c = 80 mm.