Pulverized coal particles are used in oxy-fuel combustion power plants for electricity generation. Consider a situation where coal particles are suspended in hot air flowing through a heated tube, where the convection heat transfer coefficient is 100 W/m2·K. If the average surface area and volume of the coal particles are 3.1 mm2 and 0.5 mm3, respectively, determine how much time it would take to heat the coal particles to two-thirds of the initial temperature difference.

Q: A power station uses oil-fired boilers which are supplied with fuel from 4 cylindrical tanks, each…

A: Given:Number of cylinders, n=4Cylinder diameter, D=12 mCylinder height, H=11 mCalorific value of…

Q: A 10 cm diameter aluminum ball is to be heated from 94°C to an average temperature of 140°C in 30…

A: Given that ,  Diameter D=10cm Radius r=5cm T1=94°CT2=140°Ct=30min=30×60s=1800sCp=0.91kJ/kgK

Q: An ordinary egg can be approximated as a 5.5-cm-diameter sphere whose properties are roughly k=0.6…

A:

Q: Calculate the heat transfer rate (in W) through a 2.65 m2 door with h = 0.21 W(m2•K) The temperature…

A: Given data -: The temperature of the cold air outside (To) = -12 oC = 261 K…

Q: A nuclear fuel element has the form of a plate 6 mm thick sandwiched between two stainless steel…

A: The heat generation rate is q=0.18*106 kW/m3. The thermal conductivity of an element is k=0.002…

Q: For a metal plate (k = 50 W/m°C and a = 0.000030 m^2 / s) that is at a uniform initial temperature…

A:

Q: In a manufacturing process a thin rectangular part that has a surface area of 30 cm × 30 cm and a…

A: Given, Area (A) = 30 cm X 30 cm=900 cm2=0.09 m2 Mass (m) = 3750 g Ti = 498 °K Ts= 25° C = 25+273°C =…

Q: A hot dog can be considered to be a 12 cm long cylinder, whose diameter is 2 cm and whose properties…

A: (a) The biot number is Since the biot number is greater than 0.1, thus the lumped capacitance…

Q: etermine the surface tem

A: Given: Q=0.4 W d=0.3 cm L=1.8 cm v=240 m/min air temp=35oC To determine: Surface temperature

Q: The gas at an average temperature of 160 oC is carried through a steel (steel=46 W/m2.K) pipe with…

A:

Q: A 268-ft-long section of a steam pipe whose outer diameter is 4 inches passes through an open space…

A:

Q: The 5-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k= 240 W/m·K) or copper…

A: Given:Heat transfer from the stove to the pan, Q=1200 WDiameter of pan, d=200 mm or 0.2 mthermal…

Q: During a fire, the trunks of some dry oak trees (k = 0.17 W/m·K and a = 1.28 * 10-7 m2/s) that are…

A: The properties of the dry oak tree are given as, The Biot Number is written as, Here, Biot Number…

Q: Oranges of 2.5-in-diameter (k= 0.26 Btu/h·ft·°F) and α= 1.4 10-6 ft2/s) initially at a uniform…

A:

Q: QUESTION 7 As in the previous question, steam is flowing inside a 10-cm-diameter, long pipe whose…

A:

Q: The net radiant-heat exchange between a 20-by-20 ft rough plaster panel-heated ceiling and a…

A:

Q: Determine the convection heat of a boiler if you are given the following data: Because boiling is…

A:

Q: Warm air is blown over the inner surface of the windshield of an automobile to defrost ice…

A:

Q: A 50-meter-long cast iron pipe with a 10-centimeter outside diameter goes through a 288 K…

A:

Q: Consider water (at a temperature of 276 K ) flowing inside a cylindrical pipe, having a diameter of…

A:

Q: Hot air at 79.0 oC is blown over a 3-m by 5-m flat surface at 34.9 oC. If the average convection…

A:

Q: In an annealing process, a 50-mm-thick stainless steel plate (ρ = 8238 kg/m3, cp = 468 J/kg⋅K, k =…

A:

Q: A small copper wire with a diameter of 0.792 mm and initially at 366.5 K is suddenly immersed in a…

A: Given  k = 374 W/m · K, cp = 0.389 kJ/kg · K,  ρ = 8890 kg/m3.  h = 85.2 W/m2 · K Find Time, t Heat…

Q: The components of an electronic system dissipating 180 W are located in a 4-ft-long horizontal duct…

A: The data given is Temperature inlet, Tin = 85°F Temperature inlet, Tout = 100°F  Area of cross…

Q: eat-transfer rate through the wall is q = (T1 - T2) / (1/h1A + x/kA + 1/h2A) where T1 and T2 are…

A: Given    Temperature inside the wall = T1  Temperature outside the wall = T2               Thermal…

Q: How does the science of heat transfer differ from the science of thermodynamics? Give your answers…

A: Thermodynamics and Heat Transfer both are part of thermal engineering and each has its own meaning…

Q: Cold conditioned air at 12°C is flowing inside a 1.5-cm-thick square aluminum (k = 237 W/m·K) duct…

A: Given data: The given temperature of the cold conditioned air is: Ti=12 C The thickness of the…

Q: Water enters a 2.5-cm-internal-diameter thin copper tube of a heat exchanger at 15°C at a rate of…

A:

Q: A camper has a propane-powered refrigerator. The refrigerator consumes approximately 0.50 kg of…

A:

Q: Water is to be heated from equipped with an electric outer surface of the heate transferred to the…

A: given : T₁ = 8⁰C T₂ = 80⁰C d = 3 cm = 0.03m L = 7 m V̇ = 10 L/min = 10 x10-3 m³/ 60 sec = 1.66*10-3…

Q: cylindrical fuel rod (k = 30 W/m•K) of 2 cm in diameter is encased in a concentric tube and cooled…

A: Given data is

Q: In a manufacturing facility, 2-in-diameter brassballs (k = 64.1 Btu/h·ft·°F, r = 532 lbm/ft3, and cp…

A: Let's first calculate the characteristic length and the Biot number to check whether the lumped…

Q: A 50-m-long section of a steam pipe whose outer diameter is 10 cm passes through an open space at…

A:

Q: In a large chemical factory, hot gases at 2273 K are cooled by a liquid at 373 K with gas side and…

A: Given:- Tg=2273KTf=373Khg=50W/m2Khf=1000 W/m2KL=2cm=0.02mRcr=0.05 m2K/WTo find:-Rate of heat loss, Q

Q: To defrost ice accumulated on the outer surface of an automobile windshield, warm air is blown over…

A: Given data: Thickness, t = 5 mm Thermal conductivity, k = 1.4 W/m.k Outside temperature, To = -10°C…

Q: If you add heat of magnitude 800 kJ to a mass of 800g of water originally at a temperature 75…

A: GivenQ=800kJm=800g=0.80kgTi=75oCLHV=22.6×105 J/kg=2260 kJ/kgCp=4186 J/kgK=4.186 kJ/kgK

Q: how long it will take for the thermocouple to read %95 of the initial temperature difference.

A: Given: d=1.2 mm=1.2×103 mk=35 W/m°Cρ=8500 kg/m3Cp=320 J/kg°Ch=65 W/m2°C TO determine: Time take for…

Q: Consider two flat-plate collectors with different specifications. The transmissivity, absorptivity,…

A: a) To calculate the collector efficiency, we can use the following formula:η = (τα) / [(τα) +…

Q: A transformer that is 1.5 m long, 0.062 m wide, and 0.05 m high is to be cooled by attaching a 1.5-m…

A: