Proli. 2-31. The beam is subjected to the two concentrated loads as shown. Assuming that the foundation excrts a lincarly varying load distribution on its bottom, determine the load intensities w and w, for equilibrium (a) in terms of the parameters shown: (b) set P 2 kN, L -3m. 2P sup Prots 2-31

Proli. 2-31. The beam is subjected to the two concentrated loads as shown. Assuming that the foundation excrts a lincarly varying load distribution on its bottom, determine the load intensities w and w, for equilibrium (a) in terms of the parameters shown: (b) set P 2 kN, L -3m. 2P sup Prots 2-31

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

INFLUENCE LINE PROBLEM a. Determine the maximum positive ordinate for member DC. b. Determine the location of a point load that will give the maximum compressive force for member AB. show solution asap ,answers in 4 decimal places
A bar is supported by pins at B and A. If x is one meter and w is 12 kN/m determine the diameter of the pins required. The failure shear stress for the pins is 250 MPa and a Factor of Safety of 2.0 is required. Assume the pin at B only supports a vertical reaction on the bar. Also based on the pin diameters calculated, determine the additional downward load P at the right end that could be added if the FOS is reduced to 1.5 A, B 2 m 2 m
A simply supported wood beam that is 13.2 m long carries a 41 kN concentrated load at B. The cross-sectional dimensions of the bearn are b = 125 mm, d = 350 mm, a = 110 mm, and c= 35 mm. Section a-a is located at x= 2.2 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entirespan. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P. a H a a B C K 2L 3 3 Answer: (a) TH = i 689 КРа (b) TK = i КРа 280 (c) Tmax= i 799 kPa (d) Omax= 47.11 MPa
asap please thank you
A simply supported wood beam that is 9.3 m long carries a 31 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 400 mm, a = 80 mm, and c = 30 mm. Section a-a is located at x = 1.6 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. a Н to A a В K 2L 3 3 Answer: kPa (a) TH = i kPa (b) TK = i kPa (c) Tmax = i MPa (d) Omax = i
3.75 نقطة )نقاط( السؤال 5 The beam is supported by a pin at A and a short link BC. If P = 5 kN and the diameter of the pin at C is 8 mm, determine the factor of safety against shear stress of pin .C assuming 800 MPa 2P |0.5,m 1 m-1.5 m -1.5 m- 4P 4P P. 0.5 m| 30 B 1.269 1.257 1.322 O 1.462 O
1. "ll zain IQ Qz 5 torsion.p.. Strength of materials Qz The steel shaft has a diameter of 50 mm and is fixed at end A and turn free at end B. If it is subjected to the couple, determine the maximum shear stress in regions AC and CB of the shaft. G = 75 GPa. 3 kN 3 kN 400 mm 50 mm 50 mm 600 mm
A simply supported wood beam that is 14.1 m long carries a 47 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 360 mm, a = 70 mm, andc = 20 mm. Section a-a is located at x = 2.4 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. y H a a A В K L 2L Answer: (a) TH = i kPa (b) TK = i КРа (c) Tmax = i kPa (d) Omax MPa i 13
The beam is subjected to a uniform live load of1.2 kN/mkN/m, a dead load of 0.5 kN/mkN/m, and a single live load of 45 kNkN. Assume AA and CC are roller, and BB is a short link. Follow the sign convention. The distributed live load can be applied to several segments of the beam that are not necessarily adjacent. (Figure 1) A)The beam is subjected to a uniform live load of1.2 kN/mkN/m, a dead load of 0.5 kN/mkN/m, and a single live load of 45 kNkN. Assume AA and CC are roller, and BB is a short link. Follow the sign convention. The distributed live load can be applied to several segments of the beam that are not necessarily adjacent. (Figure 1) B)Determine the maximum positive shear at EE. y D B E 4 m 4 m 4 m 4 m
If the maximum allowable force (tensile or compressive) in members GF in the pin-connected truss shown is known to be 270 kN. Determine the maximum load P that can be applied to the truss. 6 m 6 m 6m 6m 6m Select one: OA.P= 90.00 KN OB. P = 270.00 KN OC.P = 405.00 KN OD.P = 180.00 KN OE.P = 135.00 KN P.
1.Solve with correct fbd
For the truss shown below, applied loads are PB = 73 kN, PC = 36 kN and PD = 15 kN. Using the sign convention 'tension positive', select the correct answer for the axial force in member GH in kN: К F AR G В Рв 4@3m=12m O 1. The axial force in member GH is -60 kN. O2. The axial force in member GH is -78 kN. O 3. The axial force in member GH is -67.1 kN. Н Pc J D Ро K E 4m ?