PROBLEMS Question 1 The basic elements of a hydraulic press are shown in Figure 1. The plunger has an area of 3-cm, and a force, F1, can be applied to the plunger through a lever mechanism having a mechanical advantage of 8 to 1. If the large piston has an area of 150 cm², what load, F2, can be raised by a force of 30 N applied to the lever? Neglect the hydrostatic pressure variation. F2 Plunger Hydraulic fluid F1

PROBLEMS Question 1 The basic elements of a hydraulic press are shown in Figure 1. The plunger has an area of 3-cm, and a force, F1, can be applied to the plunger through a lever mechanism having a mechanical advantage of 8 to 1. If the large piston has an area of 150 cm², what load, F2, can be raised by a force of 30 N applied to the lever? Neglect the hydrostatic pressure variation. F2 Plunger Hydraulic fluid F1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 6 In the schematic below, water flows through the pipe and enters a sudden contraction nozzle. To hold the nozzle in place, calculate the axial component of an anchoring force (FA) that would be necessary. Provide a sketch of your control volume. p = 1.940 slugs/fts, 1 ft = 12 inches, 1 lb-s? = 1 slug-ft Section (1) Uniform flow P-75[psi] V,-25[ft/s] Section (2) Uniform flow P2=0 [psi] V=100[ft/s] D;=3 [in] Flow in circular pipe Flow in circular pipe Sudden contraction nozzle
A pressure gauge tester is shown in Figure 3.3. The cylinder is filled with oil, B,=475×10-1²Pa-!. The diameter of piston is D=15 mm, the screw pitch t=2mm. At the atmospheric pressure, the volume of oil in the cylinder including pipeline is V=250cm³. For the reading of 25.0MPA in the pressure gauge, how many revolutions do the handwheel must screw in? 5 4 3 2 6 1. handwheel; 2. screw; 3. piston; 4. cylinder; 5. oil; 6. pipeline; 7. standard gauge; 8. gauge to be tested Figure 3.3 A pressure gauge tester
Q2: A pressurized tank filled with oil with specific gravity, S = 0.89. If a trapezoidal plate was installed at one side of the tank as shown in Figure below. Find the total pressure force, F on the plate and its location from the liquid surface, h, When the pressure gage on the top of the tank reads 7.0 Psi. p- 7.0 Psi Air 6 ft a= 5 inch 1.6 ft b= 18 inch
complete the table also
Please be clear with your solution. Write an explanation for the formula and solution you used.
Q- A hydraulic press has a ram of 300 mm diameter and a plunger of 45 mm diameter. When the force applied at the plunger is 50 N, find the weight lifted by the hydraulic press.
Glycerin flows through a 50-mm-diameter horizontal pipe shown in (Figure 1) such that the pressure at A is PA = 113 kPa, and at B it is pa = 110 kPa. Figure Part A HÅ -3m T= Value Determine the magnitude of the shear stress that the glycerin exerts on the wall of the pipe. Express your answer using three significant figures and include the appropriate units. B. N/m² 1 of 1
I need the answer as soon as possible
please solve in SI units
3. The basic elements of a hydraulic press are shown in Fig. 1. The plunger has an area of 1cm², and a force F₁ can be applied to the plunger through a lever mechanism having a mechanical advantage of 8 to 1. If the large piston has an area of 150 cm², what load F2, can be raised by a force of 30 N applied to the lever? Neglect the hydrostatic pressure variation. Hydraulic fluid Plunger
Not sure how to do this one. Would really appreciate a full solution. Thank you!
Given; A hydraulic jack system (see figure) in an equilibrium condition, and data/properties as shown. Determine the Force F applied at the end of the lever arm to maintain equilibrium of the system. Neglect weight of plungers. Hint: Use the law of transmission pf pressure