Problem#1: An undisturbed sample of silty sand was brought to the laboratory at its natural water content, and the following measurements were made: Total mass at the natural water content: 1523.6g Mass of oven-dried sample: 1318.3g Total volume of sample: 728.2cm3 Density of the mineral solids: 2.7g/cm3 Calculate the porosity n, void ratio e, volumetric water content 0 and dry bulk density pb.

Problem#1: An undisturbed sample of silty sand was brought to the laboratory at its natural water content, and the following measurements were made: Total mass at the natural water content: 1523.6g Mass of oven-dried sample: 1318.3g Total volume of sample: 728.2cm3 Density of the mineral solids: 2.7g/cm3 Calculate the porosity n, void ratio e, volumetric water content 0 and dry bulk density pb.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A wet sand sample has a volume of 4.64 x 10-4 m3 and weighs 8 N. After oven-drying, the weight reduces to 7.5 N. Calculate the water content, void ratio, and degree of saturation.
A sample of gray silty clay has a mass of 126 kg. Laboratory tests results give a moist density(ρ) of 2.05 g/cm3, a specific gravity of solids (Gs) of 2.67, and a moisture content (w) of 14.7%.First determine all entries in the phase diagram. Then determine the void ratio (e), the porosity(n), the degree of saturation (S), the dry density (ρd), the dry unit weight (γd), and the moistunit weight (γ).
Laboratory test results for a sample of clay soil for the purpose of evaluating the potential for volume change (swelling, expansion) are shown Liquid limit = 60% %3D Plastic limit = 24% %3D Particles smaller than 0.002 mm = 44% %3D Compute the plasticity index O 44 68 O 24 O -44
Problems Pressure, o' (kg/cm?) Final height of specimen (cm) 1.9 0.25 1.763 0.5 1.742 1.0 1.702 2.0 1.656 4.0 1.604 8.0 1.550 The height of the specimen at the beginning of the test was 1.9 cm, and the diameter was 6.35 cm. The mass of the dry specimen was 91 g. Estimate the compression index and the preconsolidation pressure from the e - log o' curve. Given: G, = 2.72.
A certain saturated sand (S = 100%) has a moisture content of 27.9% and a specific gravity of solids of 2.61. It also has a maximum index void ratio of 0.90 and a minimum index void ratio of 0.33. Compute its relative density and classify its consistency. (Table on the right) Solution: Given the values of mmoisture content, specific gravity and degree of saturation, the void ratio can be estiamted as: e = Thus the relative density is found to be Dr = • According to the table, the soil is classified as %; soil. TABLE 3.3 CONSISTENCY OF COARSE-GRAINED SOILS AT VARIOUS RELATIVE DENSITIES (data from Lambe and Whitman, 1969) Relative Density, D,(%) 0-15 15-35 35-65 65-85 85-100 Classification Very loose Loose Medium denseª Dense Very dense "Lambe and Whitman used the term "medium," but "medium dense" is better because "medium" usually refers to the particle size distribution.
Following are the results of a laboratory consolidation test on a soil specimen obtained from the field: Dry mass of specimen = 128g, height of specimen at the beginning of the test = 2.54cm, Gs= 2.75, and area of the specimen = 30.68 cm². Effective pressure, o' (kN/m²) Final height of specimen at the end of consolidation (cm) 2.540 50 2.488 100 2.465 200 2.431 400 2.389 800 2.324 1600 2.225 3200 2.115 а. Plot the e-log o' curve. b. Determine the pre-consolidation pressure. Calculate the compression index, Cc. с.
You are working in a lab and are tasked with determining the percent plant available water for a particular soil sample. You take a field soil sample. The mass of your sample was 152g and it had 18.3% moisture by mass. Then, you place the soil sample in your pressure plate extractor and determine that the soil sample weighs 164.2g when the moisture potential is -33kPa and 130.7g at -1500kPa. What is the percent plant available moisture by mass of this soil sample? Please answer to one decimal place.
An undisturbed sample of fine sand is tested in the laboratory and found to have a dry mass of 4.63 kg, a total volume of 0.00198 m³ and a specific gravity of 2.70. Other laboratory tests are performed to determine the maximum and minimum density of the sand. At the maximum density, it is determined that the void ratio is 0.35 at the minimum density, the void ratio is 0.95. A. Compute the void ratio of the sand. B. Compute the relative density of the undisturbed sample. C. Compute the dry density in Mg/m³.
Problem Set 2: 4. A sample of gray silty clay has a mass of 126 kg. Laboratory tests results give a moist density (p) of 2.05 g/cm³, a specific gravity of solids (G,) of 2.71, and a moisture content (w) of 15.7%. First determine all entries in the phase diagram. Then determine the void ratio (e), the porosity (n), the degree of saturation (S), the dry density (Pa), the dry unit weight (ya), and the moist unit weight (y). Draw the Phase diagram.
a) A CU triaxial test was carried out on a silty sand soil sample. The cell pressure was equal to 200 kPa. At failure the deviator stress was equal to 410 kPa and the pore pressure was equal to 73 kPa. i) Assuming that the cohesion intercept is equal to 0, calculate the friction angle of the soil. ii) If the friction angle was equal to 35°, calculate the cohesion intercept of the soil. iii) Calculate the angle of the failure plane relative to the horizontal plane for the soil shear strength parameters in Question 4 a i and 4 a ii.
The following results were obtained by testing a sample of clay: water content 25.6%, liquid limit 43.5%, plastic limit 19.1%. From this compute the following: (a) Liquidity Index (b) Plasticity Index (c) Shrinkage Limit
Pampanga sand with Gs =2.41 is mixed 16% by weight of water and compacted to produce a cylindrical sample of 50 mm diameter and 100 mm long with 2% air porosity. Calculate the void ratio of the sample.