Problem: The machine at the production suddenly stopped The circuit was overloaded, causing the fuse to blow. 2 WHY the circuit overloaded? Bearing locked up because insufficient lubrication 3 WHY was the insufficient lubricant? 5 WHY is the pump clogged with metal? The pump strainer was broken. Solution : WHY the machine stopped? Hire new technician WHY the pump circulate oils? WHY technician did not perform inspection? Pump in good condition Replace a new strainer with correct size. WHY the pump circulate less oil? Pump clogged with metal shaving. Pump not circulating enough oil WHY the operator stopped the machine? New operator does not know the procedures

Problem: The machine at the production suddenly stopped The circuit was overloaded, causing the fuse to blow. 2 WHY the circuit overloaded? Bearing locked up because insufficient lubrication 3 WHY was the insufficient lubricant? 5 WHY is the pump clogged with metal? The pump strainer was broken. Solution : WHY the machine stopped? Hire new technician WHY the pump circulate oils? WHY technician did not perform inspection? Pump in good condition Replace a new strainer with correct size. WHY the pump circulate less oil? Pump clogged with metal shaving. Pump not circulating enough oil WHY the operator stopped the machine? New operator does not know the procedures

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If you have a three phase AC motor what is/are the losses you should take into account after converting electrical energy to mechanical energy? Select one or more: a. Mechanical Losses b. Core Losses c. Electrical or Copper Losses d. Stray Load Losses
ENGINEERING UTILITIES (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. ANSWER IN 3 DECIMAL PLACES. BOX THE FINAL ANSWER.)
What is the name of the transformer, which produces the variable output voltage? O a. Isolating Transformer O b. Power transformer O c. Current transformer O d. Auto transformer
4-pole, d.c. shunt motor has a flux per pole of 0.04 Wb and the armature is lap-wound with 720 conductors. The shunt field resistance is 240 Ω and the armature resistance is 0.2 Ω. Brush contact drop is 1V per brush. Determine the speed of the machine when running (a) as a motor taking 60 A and (b) as a generator supplying 120 A. The terminal voltage in each case is 480 V. 5 3 K4 8 Derive the Torque equation of a D.C Motor.
An electromechanical open-loop control system is shown in the figure below. The generator, driven at a constant speed, provides the field voltage for the motor. The motor has an inertia Jm and bearing friction bm. Obtain the transfer function e The generator voltage vg can be vf(s) assumed to be proportional to the field current iş.
A possible solution To counter act a temperature rise that is too high Increase the gas pressure 13. b. Increase the house blower speed c. Close some of the supply registers d. Install a more air restrictive air filter
4. Please respond to question in attached image. Thank you.
is used to In gas power plant, compress the air and same applied to combustion chamber. O a. Compressor O b. Combustion chamber O c. Turbine d. Condenser
You have measured both of the series and shunt field windings and found that each has over 10 mega ohm to ground. Your ohm meter, however indicates a resistance of 1.5 ohms across terminals S1 and S2. The ohmmeter indicates a resistance of 225 ohms between terminal F1 and F2. Are these readings normal for this type of machine, or is there likely a problem?
c) A linear sensor-transmitter is used in the flow control loop. The current transmitter output is at 8 mA when the flowrate in the pipeline is 5 m³/hr. Calculate the gain of the sensor- transmitter if the lowest value of the calibrated flow sensor is 0 m³/hr. Determine the range of the calibrated flow sensor.
23.a. Which one of the following devices can be used to accurately and conveniently measure the speed of amotor with a small slip?A. TachometerB. Revolution counter and stop watchC. Incandescent lamp and colored diskD. Stroboscope23.b. Core loss can be described asA. due to hysteresis and eddy currents in the iron parts.B. directly dependent on the load.C. caused by insufficient ventilation in the machine.D. due to eddy currents in the windings.
i need the answer quickly