Problem The following are the dimensions of a concrete T-beam section Width of flange, bf = 600 mm Thickness of flange, tf = 80 mm Width of web, bw = 300 mm Effective depth, d = 500 mm The beam is reinforced with 3-32 mm diameter bars in tension and is carrying moment of 100 kN m. Find the total compressive force in the concrete. Use n = 9

Problem The following are the dimensions of a concrete T-beam section Width of flange, bf = 600 mm Thickness of flange, tf = 80 mm Width of web, bw = 300 mm Effective depth, d = 500 mm The beam is reinforced with 3-32 mm diameter bars in tension and is carrying moment of 100 kN m. Find the total compressive force in the concrete. Use n = 9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at centre of gravity of the section. The prestress in the tendons is 1000 N/mm². Assuming modular ratio as 10, find the stress (N/mm2) in concrete.
-10 In prestressed concrete we select one of the following materials strengths: Select one: out of O a. fy = 1725 N/m2, fc= 30 N/m2 question O b. fc: = 50 N/m2, fy = 410 N/m2 O c. fy = 40 N/m2. fc = 1725 N/m2 O d. fc = 40 N/m2. fy= 1100 N/m2
1.) Given the following properties of a rectangular concrete beam: b = 280mm, d = 480 mm, f'c = 21 MPa, fy = 414 MPa. The beam is reinforced for tension only. Determine the design strength under the following conditions. a.) When the beam is reinforced with three 25 mm diameter bars. b.) When the beam is reinforced with four 25 mm diameter bars. c.) When the beam is reinforced with seven 25 mm diameter bars.
Please give me the correct solutions and answer of this problem in principles of reinforced/prestressed concrete
Q-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at centre of gravity of the section. The prestress in the tendons is 1000 N/mm². Assuming modular ratio as 10, find the stress (N/mm2) in concrete.
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6 - ø20 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = _______ Depth of uniform stress block at ultimate stage in mm to the neares whole number = _______ Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = __________
A rectangular fixed supported beam has the following properties. Compression steel if required shall have its centroid "d " mm from the extreme fiber. Calculate the required steel area (mm) at the midspan and end supports of the beam. Sketch the location of the reinforcements. Use 23.6 kN/m for the unit weight of the concrete. Round off your final answer in 3 decimal places. Given: width of beam, b = 450 mm depth of beam, h = 650 mm clear cover up to center of tension 60 mm bars= d'= 65 mm f'c = 35 MPa fy = 415 MPa wDL = 72 kN/m wLL = 63 kN/m Length of beam = 12 MIDSPAN: Required Tension Steel Area = mm? Required Compression Steel Area (if needed) - mm2 END SUPPORTS: Required Tension Steel Area = mm? Required Compression Steel Area (if needed) - mm?
The end block of a post-tensioned beam is 100 mm x 150 mm. A prestressing cable consisting of 7 wires of 6 mm dia strand and stressed to 800 MPa has to be anchored at the center of the block. The anchorage plate is 75 mm x 75 mm. If the concrete mix is M45 and the permissible bending stress in M. S. steel plate is 165 MPa, determine the thickness of the anchorage plate.
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =
SITUATION IIl: A reinforced concrete beam with a cross-section of 250mm x 460mm (60 mm steel cover). Use the following properties to calculate what is required: f'c = 20.7 MPa fy = 344.7 MPa %3D As = 3-36mm A's = 2-25mm 8) Draw the stress diagram of the beam section 9) Calculate for the depth of the compression block. 10) Calculate for the compressive strength of the concrete (in KN). 11) Calculate for the nominal moment capacity of the beam.
I need the answer quickly