PROBLEM NUMBER 1 a. Using the characteristics of Fig. 2.147b, determine p. Vp, and V, for the circuit of Fig. 2.147a. b. Repeat part (a) using the approximate model for the diode, and compare results. c. Repeat part (a) using the ideal model for the diode, and compare results. NU LAGUNA 0.33 kn V (()) FIG. 2.147

PROBLEM NUMBER 1 a. Using the characteristics of Fig. 2.147b, determine p. Vp, and V, for the circuit of Fig. 2.147a. b. Repeat part (a) using the approximate model for the diode, and compare results. c. Repeat part (a) using the ideal model for the diode, and compare results. NU LAGUNA 0.33 kn V (()) FIG. 2.147

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
5 نقاط Q3/B: Assume an ideal diode model for all the diodes in the circuit below. calculate voltages and currents through D1 and D2 R1 :: D2 9kQ.. 1N1199C ..... ... R2 D1 .... .... ... .... 18KQ 1N1199C V2 12 V R3 1kQ D3. 1N1199C ... R4 5kQ ..... .... .... .. .. ... .... .. .... .....
USING D1 1N4001G or SILICON DIODE. To sketch the characteristic curve of the diode you need to vary voltages on diode and measure current flowing during forward and reverse bias condition. Fill up the table below using circuit shown and vary battery voltages. Measure voltage and current of diode then sketch the graph. Voltage X axis and Current Y axis. Battery Diode Diode Voltage Current Voltage Battery Diode voltage Voltage 0.1V 0.3V 0.5V 0.7V 1.0V 2.0V 3.0V 10.0V Diode Current Forward Bias Condition A V 0.1V 0.5V 2.0V 5.0V 10v 20V 25V 30V Reverse Bias Condition Note: used any electronics software to perform this activity
ii) Analyse the circuit shown in below Figure. 2, assume diodes as silicon diode. Calculate: a. Vout b. IR3 c. Ip2 VCC 16V D1 D4 V3 10 V R1 2.2kQ D5 D2 Vout R3 2.8kQ IR3 Ip2 R2 4.7 kQ D3 V1 2.2 V V2 15V
Question 2: (show your detailed answer for each part of questions below) a) For the series diode configuration in the figure below, determine VD, VR and Ip. + Vn Si 10V 3 kn V b) Calculate the current through a 70 2 resistor in the circuit shown in the below figure. Assume the diodes to be of silicon and the forward resistance of each diode is ta-1 2 Show the answer steps. D Dz 70 n www 20 V DA Dy
Find the voltage(E) and current(I) of the diode in 3rd approximation with an internal resistance of 2 ohms. Choose the letter of the correct answer. 1. Current a.) 8.5mA b.) 1.4mA c.) 7.12mA d.) 9.2mA 2. Voltage a.) 0.68V b.) 0.7V c.) 1V d.) 8.3V
Determine the current V, of the figure below using the approximate equivalent model for the diode. 10 mA 2.2 k2 22 k
Solve question no.1 and show a clear and organized solution. Also, write the GIVEN and REQUIRED. Thanks!!!
The current and voltage characteristics of the Diode and the Zenner diode in the circuit in Figure 1 are on the side.has been given.a) Obtain the i-v current-voltage characteristic of the circuit.b) Find out what are the currents I, I1 and I2 for v = 5 Volts.c) Find out what are the currents I, I1 and I2 for v = -5 Volts.
Using the ideal diode model, find the output voltage for the input voltage of the following circuit and graph it in detail. (a) (b) R₁ D₁ www ww R3 D2 (a) R₁ D₁ www + + D2 R2 vo Vo R₂ (b)
I need the answer as soon as possible
Diodes would be considered ideal. Which of the following is true? 1. The DI diode is in the plug. II. The DI diode is conducting. I. Diode D2 is conducting. IV. Diode D2 is in the plug.