(c) Figure 1 shows a diode circuit with ac input Vi. Given the values of R1 = 2kN and R2 = 15k2. [Rajah 1 menunjukkan litar diod dengan masukan ac Vi. Diberikan nilai R1 = 2kQ dan R2 = 15k2.] (i) Sketch output Vo and current ir and label its appropriate values. [Lakarkan keluaran Vo dan arus ir dan labelkan nilai-nilai yang berkaitan.] (ii) Determine maximum power at resistor R2. [Tentukan kuasa maksimum pada resistor R2.] İR Vi + + R1 10V Si Vi R2 Vo -10V Figure 1

(c) Figure 1 shows a diode circuit with ac input Vi. Given the values of R1 = 2kN and R2 = 15k2. [Rajah 1 menunjukkan litar diod dengan masukan ac Vi. Diberikan nilai R1 = 2kQ dan R2 = 15k2.] (i) Sketch output Vo and current ir and label its appropriate values. [Lakarkan keluaran Vo dan arus ir dan labelkan nilai-nilai yang berkaitan.] (ii) Determine maximum power at resistor R2. [Tentukan kuasa maksimum pada resistor R2.] İR Vi + + R1 10V Si Vi R2 Vo -10V Figure 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

With the given circuit below, if the input voltage is 10 volts peak-to-peak and the diode is germanium, how much is the output voltage in volts on the negative half cycle? (put polarity (+ or -) and values only) Vpcin) V out RL
Determine the range of V₁ that will maintain V₁ at 8V and not exceed the maximum power rating of the Zener diode. Given Rs is 88ohms and RL is 0.24 kohms. . ܫܩܦܢ V₂ o PZ man Rs V₂=8V = 400 mW R₂
Use practical diode model. All diodes are Silicon.
1. Build the following circuit. Use the function generator to obtain the specified AC input voltage. D4 D1 + RL 1.2K + VsN D3 Y D2 9V sin(2n 50 t) Verify the amplı, 'de and frequency of the output waveform on the load resistor, RL. Peak voltage: Waveform period: Frequency 1.d) How much power would have. en dissipated on the diodes in total, if the same output waveform was obtainea sing a full-wave rectifier with a center- tapped transformer?
I don't know what will be the figure of example 2. Please help. Thank you.
2. For the following figure 1 employing the diode characteristics of figure 2. Determine a) DC load line b) Voltage across the resistance c) Instead of the DC source use a 10V AC source and find the AC load line. D1 charteritien DIN4002 V1 10V R1 2k R2 2k HINA Bever charateri -1A) Junetion diode characteristies, Ge and S Figure 1 Figure 2
Use Kirchhoff's law method Indicates the conduction status of the diode The result is the table of current and voltage values for each element Incorporates the diode conduction voltage if applicable 7) R1 - IK E1 R2 lov (+ D1 esi D2@s
Determine the voltage at resistor R1. (assume Zener voltage is 4 volts and Diode forward voltage is 0.7V)
Draw the symbol of Hot Barrier Diode and List its applications
For the diode circuit shown below, an IN4007 diode is used, and is connected to a variable voltage supply (VIN) that provides a maximum output voltage of 6 V. The 1N4007 diode has absolute maximum forward current rating of 1A, and can be modelled with a diode drop of 0.7 V. What is the minimum value of resistance (R1) you can use to avoid damage to the diode? Answer: Vin ww R1 O Vout
Determine the current and voltage across R1. Determine output voltage and current across R2. Voltage across all diodes. current across all diodes.
For full wave rectifier circuits a-An AC input and at least four diodes are required b-One AC input, two diodes and output load is sufficient. c-ıt can be installed with a DC source and two diodes. d-An AC, a DC source and two diodes are required.